Kenmore / Sears Range / Cooktop / Oven Parts

When I moved in to my new house I noticed there was no regulator, and the gas line was copper tubing. I ordered a regulator and ran 40 of trac pipe to make it up to code. Hooking up the regulator was easy. Read more

Ohmed the oven heat elements and oven sensor, they checked out fine. No broken or bad connections. Figured it had to be high limit switch opening or control panel. With Christmas meal around corner I ordered both. Oven working fine and my wife is happy. Read more

I purchased a new oven floor!! It only took me 15 minutes to get the other floor out & then place the new floor into position. There were only 2 screws. Read more

Unplugged the stove, unscrewed the mounting plates from the back unsnapped the wires then revered the procedure to install new one. Read more

I installed a new clock timer and overlay the job took only a few minutes and a very easy repair. Useful hint take a picture of your clock timer before you start to make sure all your wires are put back in the right order . Charles B Lafayette Tn Read more

Needed to replace burner box panel (pan under electric coil burners) and replace stove top (black panel that surrounds the burners). BB was corroded, had a couple big holes from liquid boil-overs (salted water) from the last 10 years. The stove top looked nasty. It was chipped & scratched badly. Removed electric coil burners and drip pans from stove top. Removed 1 small Phillips screw in each burner opening to detach electrical burner sockets from stove top. Lift stove top and support on prop... Read more

We took the old ones off and put the new ones on..it was easy to do ..I want to say that the girl (I think her name was Heidi) she was a big help ,she made sure that I had the right parts,I ask her to show me the picture to make sure that they look like the part ..She was a really big help. I did a survey when I ordered the parts to..Thank you for your help and the parts Anna P Read more

Quick replacement by sliding out the old filters and sliding in the new filters. Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

Ordered new bake element on 01/03/2021 and received on 01/05/2021. Thanks for the expedited service. My husband removed the old bake element and replaced with the new bake element. Took less than 15 minutes to remove and replace. Read more

Ordered new burner tubes and it was a easy install. Read more

Removed side moldings top molding and glass, removed broken handle. Reinstalled new handle, all modings and glass. Read more