Kenmore / Sears Range / Cooktop / Oven Parts

Finding the part and getting took less than three days. Installing it was simple and took only a screwdriver and 10 minutes of my time . Read more

My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

Replaced the switches. Read more

The drip pans I ordered fit my stove perfectly. I was extremely happy. I had tried drip pans from Wal Mart and Lowe's and they wouldn't sit right in the stove. Read more

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

I fallow instruction by watching video Read more

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

• Won't start
• Element will not heat

I ordered the recommended Infinite Heat Switch Kit and Element Receptacle and Wire Kit and installed them. The latter was a breeze, appearing to be exactly the same as the original, except for the wire color. The switch, though, was another story. It is a RobertShaw "replacement" part, designed, it seems, for use in the greatest number of original units as possible. The most obvious difference between this switch and the original (besides its comparatively small size) is the long, segmented... Read more

Orded rack by stove model number. fit perfect Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more

Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more

Cleaned/ soaked all burners in Ammonia and scraped off the remaining with a pumice stone. Oiled all screws. Replaced (4) ignitors or electrodes and module kit/ right front burner/ burner switch harness. Although this was the third order of switches from 3 different places including the local supplier due to the switches being manufactured upside down and lit on low on the first attempt. (Since I was going to have to open it up again to either repair or remove and return the upside-down harness... Read more

• Element will not heat

Watched the video when the part came, and 5 minutes later, our 25 year old stove is once again working like a champ. Read more

Replaced switch with back cover off and power plug pulled. The replacement switch was the same as old, was easy to pull off wires and push on new one. Also replaced torn door gasket with new one and was a exact replacement both only took less than a hour. Read more

So, after looking for replacement parts, I found these. I was delighted. My original knobs were plastic with a silver finish. They had blistered from the heat of the stove over the years. The replacement knobs were all metal. Price was right. Very happy. Read more