Kenmore / Sears Range Hinge Parts

This oven door hinge supports and guides the door so it opens and closes smoothly and seals properly. Replacing a worn hinge can restore correct door alignment and help prevent heat loss from a door that won't close tightly.

• Supports the oven door and controls its opening/closing movement
• Helps maintain proper door alignment and seal for stable temperatures
• Replace if the door won't stay closed, sags, binds, or slams
• Symptoms can include heat escaping around the door, uneven baking, or creaking/grinding when moving the door

• Disconnect power at the breaker; allow the oven to cool completely
• Remove the door; use hinge locks/pins if the design provides them
• Install the hinge in the original orientation and mounting points; re-seat the door and verify latch engagement
• Check door alignment; replacing both hinges together can help ensure even closing force

Restore smooth, secure door movement with this oven door hinge. A worn hinge can cause the door to sag or leak heat; replacing it helps the door close flush for better heat retention and consistent baking performance. What it does:

• Provides spring-tensioned pivot for the oven door
• Helps keep the door aligned and fully closed against the gasket
• Common fixes: door won't close fully, drops quickly, won't stay ajar, squeaks or binds
• Reduces heat loss and temperature fluctuation caused by a misaligned door

• One door hinge assembly

• Disconnect power at the breaker and let the oven cool completely
• Support the door; engage hinge locks or remove fasteners, then lift the door off per your model's instructions
• Remove the faulty hinge and install the new hinge in the same orientation; reuse mounting hardware
• Open and close the door to verify smooth motion and a tight seal before use

Kit includes 4 pins.

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.

This oven door hinge connects the door to the appliance frame and controls its movement. Replacing a worn hinge restores smooth, controlled operation and a proper seal to help keep heat in and cooking performance consistent. What it does:

• Supports and guides the oven door as it opens and closes
• Spring mechanism helps the door stay closed and hold at partial-open positions
• Maintains door alignment with the gasket to reduce heat loss
• Typical symptoms: door won't close fully, drops open quickly, sits uneven, or needs extra force to latch

• One hinge

• Disconnect power; turn off gas supply for gas models
• Remove the door per your owner's manual; engage hinge locks or insert hinge pins before lifting the door
• Support the door and watch for sharp edges and spring tension; wear gloves and eye protection
• Many ovens use two hinges—inspect both and replace in pairs if wear is uneven

The Range Hinge is an OEM part for Frigidaire ranges. It is a hinge component that is responsible for securely and smoothly attaching the range door to the cabinet. The hinge allows for easy opening and closing of the oven door while cooking. 

Causes of a bad hinge can include wear and tear over time, excessive force or weight placed on the door, or damage from impacts. 

Symptoms of a bad hinge include:

• The door not closing or opening fully  
• The door becoming loose or detached from the cabinet
• Noises or squeaking when operating the door
• Difficulty or resistance when opening or closing 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This oven door hinge controls and supports the door's movement, allowing it to open smoothly and close tightly. A secure, balanced hinge helps preserve the door seal and maintain consistent cooking temperatures.

• Supports door weight and balances spring tension for smooth opening and controlled closing
• Helps the door close fully against the gasket to reduce heat loss and temperature swings
• Replaces worn or bent hinges that cause sagging, slamming, or a door that won't stay closed
• Can reduce squeaks or binding and restore proper door alignment

• Disconnect power and allow the appliance to cool completely before servicing
• Remove the door; lock hinge clips or insert hinge pins before lifting the door off
• Note hinge orientation and spring tension when transferring; keep hands clear of moving spring arms
• After installation, verify door alignment and that the gasket contacts evenly all around

Replacement refrigerator door hinge that supports proper door alignment and smooth opening and closing. Restores secure door operation to prevent sagging, binding or air leaks when a hinge is worn or damaged.

• Supports and pivots the refrigerator door for stable, reliable opening and closing.
• Maintains door alignment to reduce gaps that can cause cold air loss and temperature issues.
• Designed to match factory fit and function for the door hinge mechanism.

• Disconnect power and remove food from the door before starting to reduce risk of injury or damage.
• Support the door while removing and installing the hinge to prevent it from falling or bending.
• Retain original mounting hardware; use the correct screws and torque values per the service manual.

This door hinge is a direct-fit replacement part that supports and aligns an appliance door for smooth opening and secure closing. Replacing a worn hinge restores proper fit and prevents door sag, binding, or noisy operation. What it does:

• Provides the pivot point that lets the door open and close smoothly.
• Keeps the door aligned so seals meet and the door closes fully.
• Restores stable door movement and reduces sagging or rubbing.
• Helps stop binding, unusual noises, or doors that don't stay closed.

• Disconnect power to the appliance (and water supply if applicable) before starting work.
• Support the door while removing or installing the hinge to prevent damage or injury.
• Keep original screws and mounting hardware; new fasteners may be required if originals are worn.

This hinge kit restores a refrigerator door's secure attachment so the door opens, closes and seals properly. Install to correct sagging, misalignment or noisy pivot points and help maintain consistent cabinet closure. What it does:

• Secures the appliance door to the cabinet and provides the pivot point for smooth movement
• Restores proper door alignment to help improve sealing and reduce air gaps
• Replaces worn or bent hinge hardware that can cause door sagging or rubbing
• Reduces creaks, binding or uneven door movement when operating the door

• Disconnect power to the appliance and remove food from the door before starting
• Support the door during removal and installation to prevent drops or damage
• Tighten hardware securely but avoid over-torquing; verify door alignment and seal after installation
• Follow OEM instructions for your model before ordering

This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:

• Provides a secure plug-in connection between a wire harness and a component
• Restores power to a component when the original connector is cracked, melted, or corroded
• Helps prevent loose connections that can cause intermittent operation or sparks
• Fits the OEM-style wiring configuration for a direct replacement

• Disconnect power to the appliance before starting any repair
• Remove the damaged connector and match the replacement to the harness before installing
• Use basic hand tools; avoid forcing terminals to prevent damage

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

A replacement hinge bracket that secures and aligns the refrigerator door, restoring proper pivot and fit for smooth opening and closing. Install this bracket to correct sagging or misaligned doors and improve door seal performance. What it does

• Secures the door hinge to the cabinet and supports door weight — use when the door droops or hangs unevenly.
• Maintains pivot alignment so the door opens and closes smoothly without binding.
• Helps keep the door gasket aligned for a tighter seal; can reduce uneven gaps and cold-air loss.
• Replaces bent, cracked, or worn hinge-mounting points that cause noise or instability.

• One hinge bracket.

• Disconnect power to the appliance before starting work and remove or support the door to prevent injury.
• Support the door while removing and installing the bracket; a second person may be needed for large doors.
• Reuse existing hinge hardware if undamaged; replace fasteners if stripped or missing.
• After installation, check door alignment and adjust hinge position as needed for a proper seal.

This door hinge is a factory-style replacement that restores secure, smooth door movement and proper alignment. It helps doors open and close correctly so seals work and the appliance keeps consistent temperatures. What it does

• Supports and pivots the appliance door for proper alignment and operation
• Restores secure door seating to help prevent gaps and cooling loss
• Reduces door sag, sticking, or uneven closing
• Replaces worn or damaged hinge components that cause noise or binding

• One door hinge

• Basic hand tools required; disconnect power and empty the door before starting
• Support the door during removal and installation to prevent damage or personal injury
• Inspect mating hardware and seals; replace any worn fasteners

This hinge is the replacement pivot that supports and guides a refrigerator door so it opens and closes smoothly. It restores proper door alignment and helps maintain a tight seal for efficient cooling. What it does:

• Provides a stable pivot point so the door swings freely and stays aligned
• Helps the door close fully to maintain the internal temperature and seal
• Replaces worn or damaged hinge hardware that can cause sagging or rubbing
• Reduces noise from a loose or binding door pivot

• Disconnect power to the appliance and remove contents or support the door before working to prevent injury or damage.
• Use the correct tools and keep track of mounting screws and any spacers; some installations require removing the door.
• Realign and test the door movement after installation; adjust as needed per your model's instructions.

This refrigerator door hinge secures and lets the door pivot smoothly, restoring proper door alignment and sealing for efficient cooling. It replaces a worn or damaged hinge to stop door sagging and uneven gaps. What it does

• Supports the fridge door and provides a pivot point for opening and closing
• Corrects door sag or drooping that prevents a proper seal
• Helps eliminate uneven door gaps and rubbing during operation
• Reduces air leaks that can cause temperature instability or increased run time

• Unplug the appliance or disconnect power before starting any work
• Support the door while removing and installing the hinge to prevent injury or damage
• Use appropriate hand tools; keep track of screws and any shims or bushings for reuse