Kenmore / Sears Wall Oven Panel Parts

The Oven Bottom Panel is an OEM component for Frigidaire oven models. Located on the base of the oven interior, this metal panel provides structure and support. 

Causes of a bad oven bottom panel include warping or damage due to exposure to high heat over time. Small nicks or cuts could allow heat to escape and reduce the oven's efficiency. Intentional or accidental impact during cleaning can also weaken the material.

Symptoms of a bad oven bottom panel include:

• Uneven or inefficient heat distribution within the oven
• Visible warping or damage to the panel surface
• Reduced heat retention leading to longer cook times
• Potential safety hazards if the metal is weakened

This OEM Frigidaire part is also compatible with some Kenmore models. 

The Bottom Oven and Deflector Assembly is an OEM part for GE ovens. It serves the dual purpose of acting as a base for the oven and deflecting heat for more efficient cooking.

Causes of a bad Bottom Oven and Deflector Assembly can include exposure to high heat over extended periods, accidental impact or mishandling, and general wear and tear from regular use. 

Symptoms of a bad Bottom Oven and Deflector Assembly include:

• Uneven cooking or baking results
• Visible cracks, warping, or damage to the assembly
• Unusual noises during oven operation
• Difficulty in maintaining set oven temperatures

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Bottom Oven Panel is an OEM part for Whirlpool ranges. This panel is located at the bottom of the oven cavity, protecting the internal components and providing a smooth surface for easy cleaning.

Causes of a bad Bottom Oven Panel can include exposure to excessive heat or spills, causing warping, discoloration, or damage to the panel.

Symptoms of a bad Bottom Oven Panel include:

• Visible cracks, dents, or other physical damage
• Discoloration or surface deterioration
• Loose or dislodged panel, exposing internal components

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This panel forms the floor of the oven, sitting above the bake element or burner to shield it from spills and provide a smooth, stable surface. Replace a warped or damaged panel to help maintain proper heating and easier cleanup. What it does:

• Forms the oven floor above the bake element or burner
• Shields the heat source from drips and debris to help prevent scorching and odors
• Supports designed airflow and heat distribution in the cavity
• Common replacement signs: warped or dented panel, rust or chipped finish, smoke/odors from spills beneath the panel, or uneven baking results

• 1 oven bottom panel

• Disconnect power (and shut off gas supply for gas ranges) before servicing; allow the oven to cool completely
• Remove oven racks; release front fasteners or clips and lift the old panel out of the rear tabs (method varies by model)
• Seat the new panel into rear tabs, align the front edge, and secure as originally installed
• Verify the panel sits flat and clear of the bake element or burner before reassembling

This Oven Bottom forms the floor of a gas oven cavity. Positioned above the bake burner, it shields the burner/igniter from spills while providing a smooth, removable surface that helps direct heat and is easier to clean.

• Covers and protects the bake burner and igniter assembly
• Helps channel heat and airflow across the oven cavity
• Catches drips and debris; removes for periodic cleaning
• Typical failure signs: warped or rusted panel, flaking finish, burnt-through spots, or persistent smoke from baked-on spills

• Allow the oven to cool completely; wear cut-resistant gloves—edges may be sharp
• Disconnect power and turn off gas supply before servicing
• Remove racks; release rear screws or tabs per your model, lift and slide the old panel out; seat the new panel under the front lip and secure
• Restore power and gas, then verify proper fit and clearance

This is the removable metal oven bottom for the lower oven cavity. It forms the floor above the heating components, protecting them from spills while providing a clean, even surface for baking and easier cleanup.

• Shields heating components beneath the lower-oven floor from drips and debris
• Provides a flat, durable surface inside the oven cavity
• Helps promote even heating and airflow within the oven
• Typical replacement reasons: warped or rusted panel, chipped/flaking enamel, persistent smoke/odors from burnt-on spills

• Disconnect power at the breaker and allow the oven to cool completely before service
• Remove oven racks for access
• Remove the mounting screws (often at the rear), then lift and slide the panel out
• Reinstall with existing hardware; ensure proper clearance from the heating element before restoring power

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

This component is the inner panel for a microwave oven door. This part includes the heat-resistant interior part of the microwave door. If this part sustains damage in any way, it may be less effective and will need to be replaced. This could include breaks, cracks, or dents. The glass could break and this part includes the inside door panel that contains the glass. The person performing the repair should wear gloves to protect their hands during this process. Unplug the microwave first.The microwave oven door inner panel is compatible with microwave ovens that are manufactured by Kenmore Elite, Frigidaire, and Electrolux. It is sold as an individual part. This particular part is sourced straight from the manufacturer itself.

This control panel is the user interface for your oven/range, letting you set temperatures, timers, and cooking modes from the front console. Replaces a worn or non-responsive control surface to restore normal oven control and display readability. What it does:

• Provides the touchpad/buttons and display area used to enter oven and timer functions
• Restores response when front controls are unresponsive, sticky, or intermittently working
• Replaces a cracked or faded panel that makes settings hard to read
• Works with the oven's electronic control to send user commands for bake, broil, timers, and clock

• Disconnect power to the appliance before attempting any repair
• Handle the panel carefully to avoid damaging the touch surface or display lens
• Require removal of trim or bezels; keep screws and fasteners organized

This door assembly replaces a damaged or dented fresh-food compartment door, restoring the outer panel and sealing surface for reliable cooling and a clean appearance. Fits affected Frigidaire refrigerators that use this OEM assembly. What it does:

• Replaces a dented, cracked, or warped fresh-food compartment door to restore fit and appearance
• Restores the door sealing surface to help maintain proper refrigerator temperature
• Resolves issues where the door no longer closes or aligns properly due to damage
• Replaces cosmetic damage that can expose inner components or insulation

• Disconnect power to the refrigerator before beginning any repair
• Door assemblies are heavy and bulky — have a second person or proper support during removal/installation
• Basic hand tools typically required; may need hinge alignment and adjustment after installation
• Follow the refrigerator service manual or OEM instructions for hinge hardware, alignment, and torque specifications