Kenmore / Sears Wall Oven Parts

• Little to no heat when broiling

Easy fix. Both elements replaced while I was at it, so all new. Figured if one went the other was going to follow. CIRCUIT BREAKER OFF. Removed the back metal panel with my nut driver for the hex head screws. Note where the panel may slip under tabs for support. Remove slip on electrical connections on upper and lower elements. May need a pliers. (I did not want to just pull the element and the wires into the oven with the element and remove them there, like a technician would do. After 15... Read more

Ordered all the parts Read more

• Little to no heat when broiling
• Element will not heat

Once I received the element within three days, I simply removed the other element by unclipping and unplugging lugs in rear. Placed the new one in clips and connected lugs and all was good! Read more

Replaced ignitor. Very simple project. Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

The top part of our double wall oven quit working a couple years ago. We asked an appliance repair guy if he could find a replacement heating element and after a few days, he told us he couldn't. We switched to using the bottom and recently I started looking to purchase a new oven. On a whim, I decided to check the Interwebs and found several sites claiming to have the part that the appliance repair guy said didn't exist. I ordered from Appliance Parts Pros and a few days later the... Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more

Ordered the burner bowls from you (after purchasing some locally that did not fit and were very flimsy). These bowls were very well made and fit perfectly. Heavy construction. Appears they will last a long time. Will order anything for my appliances from you in the future. Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

Ordered all the parts Read more

• Element will not heat

Replacement of the element was relatively straightforward, but there are a couple of things to be aware of before you begin. First, turn off power to the stove at the breaker box. Allow the cooktop to raise by removing the two screws that secures it on the underside of the front edge. Open the oven door to do this. Removal of the old element is simple, just remove the two screws that secure the wide mounting bracket that holds the two front elements. Carefully turn the assembly over. To... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Ordered the part, which was easy and smooth. Watched you tube video on how to repair. Took me 15 minutes. Easy as it could be. Read more

• Little to no heat when baking

Replaced with new Read more

Burners were an exact match for the originals and the pans fit perfectly. Vastly improved the appearance of an old cook top and allowed us to to not have to replace it before our home goes up for sale. Read more

Finding the proper conversion kit was a snap. I just plugged in the model number and Appliance Parts Pros sent the proper conversion kit. Read more