Kitchenaid Range / Cooktop / Oven Parts

The surface element is an OEM part for Whirlpool electric ranges. It is responsible for generating heat through its electric coils or elements on the cooktop. 

Causes of a bad surface element can include wear and tear over time, cracks or damage to the electric coils from heat stress or impact, or failure of the underlying electric components.

Symptoms of a bad surface element include:

• Slow or uneven heating of the cooktop surface
• Hot or cold spots when cooking  
• Elements failing to glow red when turned on
• Burned or charred pans and cookware
• Tripped breakers or blown fuses 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, and some Kenmore electric ranges and cooktops.

Includes lock latch motor and switch

The Grommet is an OEM part for Whirlpool cooktops. This part provides a secure fit and cushioning for the control knobs on the cooktop, ensuring smooth operation and preventing damage to the control panel.  

Causes of a bad knob grommet can include general wear and tear, exposure to high temperatures, or damage from frequent use.  

Symptoms of a bad knob grommet include:

• Loose or wobbly control knobs
• Difficulty in turning the knobs
• Knobs not staying in place or falling off
• Visible cracks or wear in the grommet

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Spring is an OEM part for Whirlpool ranges. This part provides the necessary tension to open and close the oven door smoothly. The spring ensures that the door stays securely shut during cooking and opens effortlessly when needed, contributing to the overall functionality and safety of the range.

Causes of a bad range door spring can include wear and tear over time, exposure to high temperatures, or damage from accidental impacts. 

Symptoms of a bad range door spring include:

• The oven door not staying closed
• Difficulty in opening or closing the door
• Uneven or incomplete sealing of the door
• A door that feels loose or unstable

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Burner Head is an OEM part for Whirlpool ranges. It is responsible for distributing gas to create an even flame for cooking on the stovetop. This burner head ensures efficient gas flow and optimal flame control, which are essential for consistent cooking performance.

Causes of a bad burner head can include clogging from food debris or grease, corrosion due to prolonged exposure to heat and moisture, or physical damage from impact. Such issues can obstruct gas flow and result in uneven heating or poor flame quality.

Symptoms of a bad burner head include:

• Uneven flame or poor flame control
• Difficulty igniting the burner
• Low or inconsistent heat output
• Unusual noises such as hissing or popping during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control module generates and manages ignition spark for DSI-equipped gas ovens/ranges. Replacing a failed unit restores reliable burner lighting and can resolve issues such as no spark, repeated clicking, or the oven/broiler not igniting.

• Generates high-voltage pulses to ignite gas at the DSI electrodes
• Times and controls ignition cycles; energizes the gas valve only during commanded ignition
• Monitors flame presence through the sense circuit and may retry or lock out if ignition fails
• Common symptoms of failure: oven or broiler won't ignite/heat, no clicking/spark, intermittent ignition, or continuous clicking
• Intended for models that use direct-spark (DSI) ignition systems, not glow-bar/hot-surface igniters

• Disconnect power and shut off gas supply before servicing
• Handle the control as an electrostatic-sensitive device; avoid touching terminals
• Transfer wires one at a time and mount the module securely with a proper ground
• After reassembly, restore utilities and verify normal ignition operation

This genuine OEM replacement part is a switch membrane touchpad made for ovens. The switch membrane touchpad is the plastic display piece on the oven that holds the buttons that control the oven's essential functions. If the touchpad is worn out and the buttons are no longer responding when pushed, it might be time to replace the touchpad. Luckily replacing this part is not a difficult repair.To replace a damaged touchpad, make sure to turn off all power to the oven by unplugging the appliance or shutting off the circuit breaker. After the power to the oven is turned off, take a putty knife to pry off the old touchpad cover. Gently pull it away from the stove's control panel until it comes off. There should be enough adhesive left over to place the new touchpad back to its original place. Be sure to line up the touchpad so that it fits perfectly. This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand ovens.

This leveling foot adjusts the appliance's height at the front to keep the cabinet stable and level. A properly leveled unit helps reduce vibration and noise and ensures doors, drums, and drawers operate smoothly.

• Supports the appliance and provides front height adjustment
• Helps correct rocking, vibration, and excessive noise from an unlevel appliance
• Can improve door alignment and smooth operation when the cabinet is leveled
• Common wear or damage can cause wobbling or difficulty staying level

• Unplug the appliance and, if applicable, turn off the water supply before servicing
• Tip or lift the unit carefully; use a helper to avoid injury
• Thread the new foot into the base and adjust until the cabinet is level and stable
• Tighten any applicable lock nut and recheck level after repositioning the appliance

Used with the 30" model.

This oven door gasket forms a heat-resistant seal between the oven door and the front frame. Replacing a worn seal helps the oven reach and maintain set temperatures and keeps hot air and steam from leaking around the door.

• Seals the oven cavity perimeter to limit heat and steam escape
• Helps the oven preheat properly and hold a consistent temperature
• Can help with symptoms like heat leaking at the door, longer preheat times, and uneven baking
• Replace if the gasket is torn, flattened, brittle, or visibly frayed

• Disconnect power at the breaker; allow the oven to cool completely (shut off gas supply if applicable)
• Pull the old gasket straight out of the retainers/clips, noting orientation and clip locations
• Clean the mounting area; press the new gasket into the retainers without stretching, seating corners fully
• Close the door to check fit and adjust seating as needed, then run a short heat cycle to condition the seal

The Oven Thermal Fuse is an OEM part for Whirlpool ranges. This safety device shuts off the oven if it overheats, preventing potential damage or fire hazards.

Common reasons for a fuse blowing include electrical malfunctions, overheating, or wear and tear over time.

Symptoms of a bad thermal fuse include:

• The oven not heating up
• The oven shutting off unexpectedly
• No response from the oven when turned on
• Error codes indicating a thermal fuse issue

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Note:  For the 230F thermal fuse with the two insulated female terminals 3/16 inch and 1/4 inch order WP4451042.

This T.O.D. thermostat is a temperature-sensitive safety switch used in select ovens and ranges. It opens or closes the circuit at a set temperature to protect components and help restore safe, reliable operation when the original device fails. What it does:

• Monitors appliance temperature and switches the circuit at its preset threshold
• Helps prevent overheat conditions that can trigger shutdowns or error codes
• Common failure signs: oven won't heat or shuts off mid-cycle; cooling fan won't run or runs constantly; recurring over-temperature warnings
• On some models it controls a heating circuit; on others it governs the cooling fan

• 1 thermostat (T.O.D.), SPST

• Disconnect power at the breaker and allow the appliance to cool completely before service
• Access location varies by model
• Transfer wires one at a time to the new thermostat and mount it flush for proper sensing
• Inspect for blocked vents, a failed cooling fan, or shorted elements before returning the unit to service

Color: Black. Kit includes five burner caps. For the burner cap kit in grey use part number WPW10183372.

This surface burner infinite switch regulates power to a cooktop element, letting you set and maintain the heat you choose. Replace a worn control to restore accurate temperature adjustment and reliable on/off operation.

• Regulates on/off cycling of power to the surface element to achieve the selected heat level
• Helps address issues like a burner that won't heat, is stuck on high, heats inconsistently, or won't turn off
• Restores smooth temperature changes as you turn the control knob
• Typical failure signs include dead burner, runaway heat, or erratic temperature control

• Disconnect power to the range or cooktop at the breaker before servicing
• Remove the control knob and open the control/back panel to access the switch
• Tag and transfer wires one at a time to the matching terminals on the new switch
• Reassemble and test the burner from low to high to confirm proper cycling

This safety thermal fuse protects your appliance by opening the circuit if internal temperatures climb too high, helping prevent overheating damage and restoring safe operation when replaced.

• Monitors temperature and cuts power if an overheat condition occurs
• Common failure symptoms: appliance won't start, no power to key components, intermittent shutoff after heating, or blown/failed continuity on the fuse
• Helps safeguard wiring and control components from heat-related failures

• Disconnect power and shut off utilities before servicing
• Access location; note wire orientation for reassembly
• Replace if open/no continuity
• Investigate and correct the root cause of overheating (vents, fans, wiring) before restoring power

This oven door hinge will work for either the left or right side of an oven door. The hinges on the door are responsible for ensuring that the door can open and close properly. If one or both of the hinges are not working correctly, the door may become difficult to open and close or may not stay on the oven. If this happens, the hinges should be replaced before using the oven.Made of durable metal, the oven door hinges should last a long time. However, they can become damaged and may need to be replaced. If there is too much pressure placed on the door or hinges, it could cause them to break. Owners may want to replace both of the hinges at the same time. Be sure that the oven is off and cooled before replacing this part.The oven door hinges are for use with certain ovens from KitchenAid, Whirlpool, Inglis, and Kenmore. The hinges are genuine OEM replacement parts sourced from the manufacturer. Each hinge is sold individually. Owners that need to replace both hinges should buy two.