Kitchenaid Range Parts

Glass scraper tool for cleaning cooktop surfaces. Removes stuck-on food, spills, and residue from glass cooktops. Essential for maintaining appearance.

Oven light not turning on when door opens? This door-activated switch detects door position and controls interior lighting. Easy push-in installation.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

The Cooktop is an OEM part for Whirlpool ranges. It is the glass surface that is used for warming and cooking food. This cooktop features multiple warming zones with varying heat levels to accommodate different types of cooking needs. It has a smooth glass design that is easy to clean.

Causes can be general wear and tear from frequent use. Accidental impacts or stresses from heavy cookware can also damage the cooktop.

Symptoms of a bad cooktop include:

• Zones not heating up properly or uneven heating
• Cracks or breaks in the glass surface
• Dirty burners that leave residue
• Warping or discoloration of the glass over time

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is the base component of a surface burner on a gas or electric range cooktop. It sits on the cooktop and distributes heat evenly for cooking. Replace this burner base if you notice uneven flame patterns, visible damage or warping, or if the burner cap no longer seats properly.

6,000 BTU. Color: Coal matte black. Measures about 2 inches in diameter.

Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.

This orifice spud meters gas to the burner for a consistent, correctly sized flame. Replace a clogged or damaged spud to restore proper burner output and reliable ignition on your gas cooktop or range.

• Controls and meters gas flow through a calibrated opening to the burner
• Helps ensure proper flame size and color when matched to the correct burner and fuel type
• Common symptoms of a failing or clogged spud: weak or uneven flame, yellow tipping, or delayed ignition
• Damaged threads or a stripped orifice can prevent correct sealing and fuel delivery

• Shut off gas supply and disconnect power; allow the appliance to cool
• Access the orifice holder/manifold for the affected burner; remove the old spud with an appropriate orifice wrench or nut driver
• Start the new spud by hand to avoid cross-threading; tighten snugly—do not overtighten brass threads
• Restore gas and check for leaks with an approved leak-detection solution; verify flame quality and adjust per the service manual

Replace a worn, cracked, or broken microwave door hinge to restore smooth door movement and proper alignment. Ensures the door opens, closes, and seals.

Pressure regulator for gas ranges and cooktops. Mounts to the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.

Secures the gas orifice beneath your cooktop and routes gas to the burner head. Replace if cracked, damaged, or missing to restore proper alignment.

Replace a cracked, stripped, or missing control knob on your electric range. This knob snaps onto the control shaft for accurate cycle and temperature selection.

Controls gas flow and pressure to burners and oven in gas ranges. Replace if leaking, cracked, or damaged to restore safe gas distribution.

This fixed thermostat switches near 60C to control a heat-managed circuit—often the oven's cooling/blower fan. Replacing a failed unit restores proper fan cycling and helps protect the control area from excessive heat during and after cooking.

• Monitors temperature in the oven cabinet/control area and switches power based on heat level
• Cycles the cooling/blower fan on and off to manage cabinet temperature
• Helps safeguard electronic controls from heat buildup
• Failure may cause symptoms such as a fan that won't run, a fan that runs continuously, or an unusually hot control area

• Disconnect power at the breaker before servicing
• Access the thermostat per your model; it is typically mounted to a plenum or bracket near the oven cavity
• Move wires one at a time and mount the new thermostat flat against the surface for accurate sensing
• Restore power and verify the fan cycles during operation

LF, LR, RR Stainless

Broil element stopped heating or browning food? This upper oven heating element restores broiling function. Easy DIY fix—unplug, remove screws, swap.