Kitchenaid Refrigerator Compressor & Sealed System

The Compressor is an OEM part for Whirlpool refrigerators. It is the main component responsible for cooling the fridge interior and freezing food. The compressor operates the refrigeration cycle by compressing and condensing refrigerant which allows for the critical exchange of heat.

Symptoms of a bad compressor include:

• Inconsistent or fluctuating interior temperatures  
• Frozen foods not freezing properly
• Abnormal vibrations or sounds emanating from the rear of the fridge
• The fridge failing to cool at all

Causes of compressor failure can be a gradual decline in performance over many years of use. Manufacturing defects or damage from moisture or impact can also cause premature failure.

Note: Includes start device, capacitor, drier, and grommets. Also, order tubing kit AP3083228

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This sealed-system compressor circulates refrigerant to cool your refrigerator, restoring normal cooling performance when the compressor fails. Designed to replace a failing compressor and help bring temperatures back to safe food-storage levels. What it does:

• Compresses and circulates refrigerant through the sealed refrigeration circuit
• Restores cooling when the compressor motor runs properly
• Commonly linked to symptoms like weak or no cooling, loud humming or clattering sounds, or a refrigerator that cycles continuously
• May be the cause if the appliance frequently trips a circuit breaker or shows hard-starting behavior

• Sealed-system work requires certified HVAC/refrigeration service and proper refrigerant handling per local regulations
• Disconnect power before beginning any repair; follow lockout/tagout practices
• Compressor replacement often requires system evacuation, brazing, and recharge — do not attempt unless qualified
• Use the identical replacement part number and follow OEM service instructions to avoid damage

This refrigerator compressor circulates refrigerant to cool the appliance and restore proper temperatures. Replaces a failed compressor to help the refrigerator maintain set temperatures when the cooling system is compromised. What it does:

• Pumps refrigerant through the sealed cooling system to enable heat exchange and cooling.
• Runs the refrigeration cycle so the refrigerator and freezer can reach and hold target temperatures.
• Common symptom linkage: fridge not cooling, compressor humming or not running, or frequent cycling.
• Can cause system pressure issues if damaged or leaking.

• One compressor (single sealed unit)

• Power should be disconnected before beginning work and the refrigerant must be recovered per regulations.
• System evacuation, leak testing, and proper recharge with the correct refrigerant are necessary after replacement.
• May require replacement of mounting hardware, start device, or filter-drier—verify system condition during service.

This heat transfer tube routes heated air or refrigerant where needed to support proper appliance temperature control and operation. It replaces a cracked or damaged transfer tube to restore correct airflow/heat routing and prevent leaks. What it does

• Channels heated air/refrigerant between system components to maintain designed heat flow
• Helps prevent heat loss or refrigerant leakage caused by cracks, breaks, or corrosion
• Often replaced when owners notice reduced heating performance, unusual temperature swings, or visible damage
• Supports safe operation by maintaining proper routing of hot air/refrigerant within the appliance

• One heat transfer tube as shown

• Follow OEM service manual for proper routing and secure fittings
• Inspect adjoining seals, clamps and connectors and replace if damaged to ensure a proper seal
• Disconnect power and, if applicable, refrigerant lines or heating elements per safety procedures before replacing
• Do not overtighten fittings; check for leaks and proper airflow/temperature after installation

This replacement water fill tube routes water to the appliance's dispenser/ice system so you get proper fill and reduced leaks. It restores reliable water delivery when the original tube is cracked or clogged. What it does:

• Directs water from the supply to the dispenser or ice/water mechanism
• Prevents leaks when intact and properly secured
• Helps ensure consistent water flow for ice makers and dispensers
• Worn or damaged tubes can cause pooling, low water delivery, or intermittent filling

• One replacement water fill tube

• Turn off the appliance power and water supply before starting work
• Inspect fittings and seals; replace clamps or gaskets if worn
• Slide tube into place and secure with the original or new clamps for a leak-free connection

This replacement tube routes fluids within the appliance to restore proper water flow and prevent leaks. It's a direct-fit service part that replaces a worn, cracked or damaged tube so the appliance moves water where it should. What it does

• Channels water/condensate between components to maintain normal operation
• Helps stop leaks or puddling caused by a cracked or split tube
• Reduces poor performance symptoms tied to restricted or damaged tubing
• Restores the original routing and connection points when properly installed

• One replacement tube as shown

• Inspect routing and connection points; replace any damaged clamps or grommets
• Turn off power and water supply before starting any repair
• Use proper clamps to secure both ends and check for leaks after reassembly

This replacement tube routes water where the appliance needs it and restores proper flow when the original tube is cracked or blocked. It's a direct-fit plumbing piece used inside the appliance to channel water safely. What it does:

• Carries water between internal components to enable normal appliance operation
• Helps prevent leaks when intact and correctly installed
• Replaces tubes that are cracked, split, clogged, or otherwise damaged
• Can stop symptoms like intermittent draining, visible leaking, or reduced water flow

• Disconnect power and shut off the water supply before starting any repair
• Verify tubing orientation and secure all fittings and clamps to prevent leaks
• Inspect adjacent fittings and seals; replace any worn hardware to ensure a tight connection

This replacement tube restores proper fluid routing between appliance components to stop leaks and poor flow. It's the OEM-design part used where a damaged or cracked tube causes performance issues. What it does:

• Routes water or drain flow between internal components to maintain normal operation
• Prevents leaks caused by cracked, brittle, or separated tubing
• Helps resolve symptoms like visible dripping, pooling, or inconsistent water delivery
• Restores a sealed connection when original tubing has deteriorated

• Disconnect power and shut off water supply before starting any repair
• Inspect mating fittings and clamps; replace worn clamps or seals as needed
• Slide tube fully onto fittings and secure with appropriate clamps to prevent leaks
• Run a short cycle to check for leaks after installation