Kitchenaid Refrigerator Screws, Nuts, Washers

This factory replacement screw secures appliance components. It replaces missing or worn hardware to restore a tight, aligned fit for panels, brackets, and assemblies—reducing rattles and keeping parts firmly in place during everyday use.

• Fastens covers, brackets, trim, or internal assemblies to the cabinet/frame
• Replaces stripped, rusted, or missing hardware
• Helps correct loose or misaligned panels or handles
• Can reduce vibration noise caused by unsecured parts

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver/bit; hand-start threads to avoid cross-threading
• Tighten snugly without overtightening to prevent damage
• Replace any companion clips or grommets if worn

This genuine replacement screw secures a refrigerator/freezer door stop so the door opens and closes correctly. It restores proper door positioning and helps prevent the door from coming off its stop or shifting during use. What it does:

• Fastens the door stop assembly to the cabinet or hinge bracket so the door stops at the correct position
• Helps eliminate door misalignment, excessive travel, or doors that swing too far
• Used where a small machine screw is required to hold the stop in place
• Simple, low-profile fastener designed for reliable, long-term hold

• Verify the screw matches the removed fastener in length and thread before installing
• Use appropriate screwdriver and avoid over-tightening to prevent strip or damage
• Disconnect power only if working near energized components; otherwise follow basic safety and appliance manufacturer instructions
• Check hinge/stop components for wear

6 - 19 x .250

This is a genuine replacement mounting screw used to secure appliance panels and components, restoring proper fit and preventing loose parts. It's a simple, low-cost fix to keep your appliance stable and quiet. What it does

• Fastens panels, trim, brackets or small components to the appliance frame
• Restores secure fit when original screws are missing, stripped, or corroded
• Helps stop rattling, vibration, or parts shifting during operation
• Works wherever the original matching screw was used

• Disconnect power (and water, if applicable) before accessing internal parts
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to prevent thread damage or cracking
• Keep small parts away from children and pets

This replacement screw is a small fastener used to secure appliance panels and components. It restores lost or damaged screws so parts stay mounted and appliances run quietly and safely. What it does:

• Secures panels, trim, brackets or housings to prevent rattling and movement
• Replaces missing or stripped screws that allow parts to come loose
• Helps maintain correct alignment of assemblies for safe operation
• Small hardware solution for common repair and reassembly needs

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid cam-out or damage
• Do not overtighten; snug until secure to avoid stripping threads or cracking plastic
• Keep small parts away from children and pets

This genuine replacement screw secures appliance panels and components, restoring proper fit and stopping movement. Use it when a missing or damaged fastener causes loose trim or rattling. What it does

• Secures panels, brackets, and small assemblies to restore proper fit
• Helps eliminate rattling, vibration, or misaligned trim caused by a missing or stripped screw
• Replaces lost or damaged fasteners during maintenance or part replacement
• Matches OEM fit for reliable fastening where specified in diagrams

• Use the matching screw location shown in the appliance diagram; do not force or overtighten
• Use the correct screwdriver or bit to avoid stripping the head
• Disconnect power and follow appliance safety procedures before accessing internal components
• If threads are damaged, replace with the correct OEM fastener rather than reusing a compromised hole

A single replacement screw used to secure appliance panels and components. Restores proper fastening to reduce vibration and keep parts aligned for safe, quiet operation. What it does:

• Fastens panels, brackets or assemblies to the appliance frame
• Helps eliminate rattling or looseness from unsecured parts
• Maintains component alignment for reliable operation
• Matches the OEM fastening point and thread where specified

• Disconnect power and water before beginning work
• Use the correct screwdriver or bit to avoid stripping the head
• Install in the original location and hand-start threads to avoid cross-threading
• Do not overtighten; tighten to snug fit per service literature

This replacement screw secures panels, trim pieces and small assemblies so covers and components stay aligned and rattle-free. It's a simple, direct fastening part used when an original screw is missing or damaged. What it does:

• Fastens panels, trim, control housings and other small components to the appliance chassis
• Replaces missing, worn or stripped screws that cause loose panels or rattling noises
• Restores correct alignment of covers and trims after service or disassembly
• Provides a direct, hardware-level repair instead of temporary fixes

• Disconnect power (and gas, where applicable) and ensure the appliance is cool before starting.
• Use the correct screwdriver bit and turn until snug; do not overtighten to avoid stripping threads or damaging parts.
• Keep removed hardware for reference; replace like-for-like if threads or inserts are damaged.
• Wear eye protection and gloves when working on appliances.