Kitchenaid Refrigerator Wire, Harness, Power Cord

This wire harness routes power and signals between key components for consistent performance. Replacing a damaged harness restores reliable connections and correct operation of affected controls, motors, or sensors.

• Distributes electrical power and control signals between boards, switches, sensors, and motors
• Replaces cut, brittle, burned, or corroded wires and terminals that cause connection faults
• Common symptoms include intermittent operation, a component that won't run, or error codes related to poor connections
• Restores proper wire routing when installed in the factory path and secured with clips/ties

• Disconnect power before servicing; turn off water or gas supply if applicable
• Photograph and label existing connections; move plugs one at a time to the new harness
• Route along the original path; secure in clips/ties and keep clear of sharp, hot, or moving parts
• Seat each connector fully by the plug body (do not pull on wires); inspect mating terminals for heat damage

This is a replacement wire harness that restores the electrical connections between the appliance control and internal components so controls and motors receive power and signals reliably. Use this harness to repair broken, damaged, or corroded wiring. What it does:

• Connects control board, switches, motors and sensors so the appliance operates correctly
• Replaces frayed or damaged wiring that can cause intermittent operation or loss of function
• Helps eliminate faults caused by broken connector ends or open circuits
• Resolve symptoms like no power to components, intermittent operation, or control communication errors

• One complete wire harness assembly

• Disconnect power before starting any repair to avoid electric shock
• Match connector shapes and colors; route harness along original clips and channels to prevent pinching
• Inspect mating connectors and terminals; replace if corroded or damaged

This wire harness routes power and signals between the appliance control and components to restore electrical connections and reliable operation. It replaces a damaged or burnt harness to help return normal function. What it does:

• Connects the control board to motors, sensors and switches so circuits operate as intended
• Replaces cracked, frayed or melted wiring that can cause intermittent or no operation
• Helps stop electrical arcing or shorts caused by damaged insulation or loose terminals
• Addresses symptoms such as control failures, no power to components, or erratic operation

• One complete wire harness as pictured

• Disconnect power to the appliance before beginning any repair to avoid shock or damage
• Handle connectors by the bodies, not the wires; ensure all terminals seat fully
• Verify wire routing and strain relief match the original to prevent pinching or chafing

The Wire Harness is an OEM part for Whirlpool refrigerators. It provides the electrical connection between various parts of the refrigerator, ensuring proper communication and voltage.

A bad wire harness can occur due to wear and tear, electrical malfunctions, or damage to the wiring itself. If you notice symptoms such as the refrigerator not cooling properly, erratic behavior, or error codes displayed on the control panel, it may be time to replace the wire harness.

Symptoms of a bad wire harness include:

• Inconsistent cooling or inadequate temperature control
• Erratic behavior or unusual noises coming from the refrigerator
• Error codes displayed on the control panel

Repair your refrigerator by replacing the faulty or damaged wire harness with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This is a replacement wire harness that restores electrical connections between components so your appliance powers and controls operate correctly. It provides the factory-style wiring needed for reliable signal and power routing. What it does

• Carries power and control signals between major components so circuits can operate as intended
• Commonly used when damaged, melted, cut, or corroded wires cause intermittent operation or loss of function
• Can resolve symptoms such as components not receiving power, control buttons or lights not responding, or erratic behavior due to open/shorted wiring
• Matches OEM routing and connector ends to maintain original fit and connections

• One complete wire harness assembly as shown

• Disconnect all power (unplug or shut off breaker) before starting any repair
• Note wire routing and connector locations or take photos before removal to ensure correct reassembly
• Inspect connectors and mounting clips; replace any broken retainers to prevent chafing or strain

This wire harness is the factory-style wiring assembly that routes power and signals between components, restoring reliable electrical connections for safe appliance operation. Replace a damaged or burned harness to reestablish proper power and control function. What it does:

• Carries power and control signals between controls, motors, switches, and sensors
• Restores lost or intermittent power caused by frayed, broken, or burned wires
• Prevents shorts and arcing from damaged insulation or loose connectors
• Ensures correct connector routing for dependable component operation

• Disconnect power (unplug or shut off breaker) before starting any repair
• Compare new harness to the old part for connector type, length, and routing before installation
• Route wires along the original paths and secure all clips and fasteners to avoid rubbing or heat contact

This dispenser harness is the wiring assembly that connects the refrigerator dispenser components to power and control signals, restoring electrical continuity so the dispenser, water, or ice functions can operate correctly. What it does:

• Routes power and signal connections between the dispenser controls and the appliance wiring
• Replaces damaged or corroded wiring that can cause intermittent dispenser, water, or ice operation
• Restores reliable connector fit and electrical contact to resolve connection-related faults
• Works with dispenser switches, solenoids, and control modules that use this harness

• Disconnect power to the appliance before starting any repair to avoid shock
• Inspect connectors and routing; match connector shapes and terminal counts before connecting
• Secure the harness away from moving parts and sharp edges to prevent wear

This wire harness assembly connects the appliance's control components to power and sensors, restoring reliable electrical signaling and operation. Use it when damaged wiring or connector failures cause power or control faults. What it does:

• Routes electrical power and signals between the control board, user interface, and major components
• Replaces frayed, burned, or broken wiring that can cause intermittent or lost control functions
• Restores proper connector fit for secure electrical connections
• Helps resolve symptoms such as unresponsive controls, intermittent operation, or visible wire damage

• Disconnect power before servicing to avoid shock or injury
• Verify connectors match and seat fully; replace any damaged clips or fasteners
• Handle connectors by the plug bodies—avoid pulling on wires

This wire assembly is the appliance wiring harness that connects controls and components to deliver power and signals. It restores reliable electrical connections and replaces damaged or frayed wiring to help your appliance operate safely. What it does:

• Routes power and control signals between components and the control board or switch
• Replaces broken, frayed, or burned wires that can cause intermittent operation or no power
• Helps stop electrical arcing and poor connections that may lead to erratic behavior
• Restores secure plug-and-socket connections for a stable electrical path

• One wire assembly (harness) as shown

• Always disconnect the appliance from power (unplug or switch off breaker) before starting
• Note wire routing and connector orientation or take photos to ensure correct reinstallation
• Handle connectors by the plug bodies, not the wires, and avoid pinching or stretching leads
• If you see heat damage or melted insulation on mating components, inspect and replace those parts as needed