Lg Dryer Parts

The Door Hinge is an OEM part for LG dryers. This hinge supports the dryer door, allowing it to open and close smoothly and securely. It ensures that the door stays aligned and functions properly, providing reliable access to the dryer drum for loading and unloading clothes.

Causes of a bad door hinge can include frequent use leading to wear and tear, physical damage from forceful opening or closing, and rust or corrosion due to exposure to moisture.

Symptoms of a bad door hinge include:

• Difficulty in opening or closing the dryer door
• The door not staying aligned or becoming loose
• Squeaking or grinding noises when moving the door
• Visible damage, bending, or rust on the hinge

This OEM LG part is also compatible with some Kenmore models.

This moisture sensor connector assembly links the dryer's sensor bars to the control to monitor fabric dryness and adjust cycle time. Replacing a damaged or loose harness restores consistent Auto Dry operation.

• Connects the moisture sensor bars to the main control for Auto Dry feedback
• Transmits the low-voltage signal used to determine when clothes are dry
• Failure may cause Auto Dry to end too soon, run too long, or deliver inconsistent results
• Typical issues include broken wires, loose/corroded terminals, or a heat-damaged plug

• Disconnect power; if gas, shut off gas supply before service
• Access the moisture sensor area at the front/lint housing
• Match routing and clips, seat terminals fully on the sensor tabs, and secure the connector
• Keep wiring clear of sharp edges and moving parts; reassemble and test a Sensor Dry cycle

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

The Door Strike is an OEM part for LG dryers. This part engages with the door catch to keep the dryer door securely closed during operation. The door strike is essential for ensuring the door remains tightly shut, allowing the dryer to function efficiently and safely.

Causes of a bad door strike can include wear and tear from regular use, damage from slamming the door, or misalignment issues that prevent it from engaging properly with the door catch. 

Symptoms of a bad door strike include:

• The dryer door not staying closed
• The dryer not starting due to the door not being securely latched
• Difficulty in latching the door
• Visible damage or wear on the strike

This OEM LG part is also compatible with Sears/Kenmore.

The Pressure Sensor is an OEM replacement part for LG dryers. This sensor monitors the airflow or pressure within the dryer, helping to regulate drying cycles and ensure efficient operation. By detecting blockages or changes in airflow, it plays a critical role in maintaining proper performance and preventing overheating.

Over time, the pressure sensor can fail due to wear, electrical issues, or buildup of lint and debris. Damage to the sensor or its connections can cause the dryer to operate inefficiently or stop functioning altogether.

Symptoms of a bad pressure sensor include:

• Dryer not heating properly
• Extended drying times
• Error codes related to airflow or pressure
• Dryer shutting off unexpectedly during cycles

This OEM LG part is also compatible with Sears/Kenmore dryers.

This drying rack sits inside the dryer drum to hold items that shouldn't tumble. It keeps shoes, sweaters, and other delicates stationary so they dry gently using the dryer's airflow and heat.

• Provides a stationary platform in the drum for rack-dry items
• Helps dry shoes, hats, sweaters, and stuffed toys without tumbling
• Replace if the rack is cracked, warped, missing, or won't stay seated
• Enables use of the rack-dry feature on compatible models

• Disconnect power and let the dryer cool before installation
• Open the door and slide the rack into the designated guides until fully seated and level
• Place items flat on the rack; avoid overloading or letting items hang over the edges
• Remove the rack before running regular tumble cycles

The Left Hand Drawer Slider is an OEM part for LG laundry pedestals. It provides stability and support to the drawer, preventing it from jamming or becoming misaligned during use.

Causes of a faulty left-hand drawer slider can include wear and tear over time, damage due to excessive weight or force, or a broken or worn-out roller mechanism. These factors can result in the drawer becoming difficult to open or close, or it not sliding smoothly.

Symptoms of a bad left-hand drawer slider may include:

• Difficulty in opening or closing the left-hand drawer
• The drawer not sliding smoothly or getting stuck
• Uneven alignment or wobbling of the drawer

This OEM LG part can also be used on Kenmore/Sears appliances. 

Note: This is for the left-hand side only. For the right side, order part number 4276ER0001A.

This door gasket seals the dryer door opening to keep heat and moisture inside the drum. Replacing a worn gasket helps restore proper airflow and drying performance while reducing lint and warm air leaking around the door.

• Creates a tight seal between the door and front panel to prevent air leaks
• Helps maintain correct airflow for efficient, consistent drying
• Reduces escaping heat and humidity around the door area
• Common signs it's failing: visible wear or tears, flattened/compressed gasket, lint accumulation near the door, longer dry times, warm air leaking when the door is closed

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the door assembly as needed and separate door panels to access the gasket (procedure varies by model)
• Remove the old gasket and clean the mating groove/surface of residue and debris
• Press the new gasket fully and evenly into place; align the seam, reassemble the door, and verify an even seal

This drying rack sits inside the dryer drum to hold items stationary while warm air circulates around them. It lets you rack-dry shoes and delicates without tumbling, helping prevent banging and scuffing that can happen when items rotate. What it does:

• Provides a stable platform inside the drum for stationary drying
• Allows heated air to circulate around items while preventing tumbling
• Used for shoes, sweaters, hats, and other items approved for rack-dry cycles
• If missing or damaged (cracked frame, broken tabs, poor seating), you may hear rattling or be unable to rack-dry items

• 1 drying rack

• Disconnect power and allow the drum to cool before inserting or removing the rack
• Insert the rear of the rack into the drum supports, then rest the front edge on the door opening; ensure it is level and fully seated
• Load items evenly and do not overload; use the rack-dry or low-heat settings recommended in your owner's manual
• Remove the rack before resuming standard tumble cycles

The Gas Valve Assembly is an OEM replacement part for LG gas dryers. It precisely controls the flow of gas to the burner unit during drying cycles. 

Symptoms of a faulty gas valve include: 

• Inadequate or inconsistent heating 
• Burner failure to ignite properly
• Error codes related to gas or pilot light issues

Causes may involve wear and tear of valve seals over extended use, blockages limiting gas flow, or damage like dents that compromise valve integrity.

This authentic LG assembly is compatible with select Kenmore brand models. 

The Drum Seal is an OEM part for LG dryers. It forms an airtight seal between the rotating drum and stationary outer housing. This seal prevents air leakage that could diminish drying effectiveness.

Causes of a bad drum seal can include cracks or breaks from heat cycling over time, hardening and failure of rubber seal materials, or physical damage from cleaning tools or debris inside the drum.

Symptoms of a bad drum seal include:

• Slow or incomplete drying times
• Clothes not feeling fully dry at the end of cycles
• Excessively long heating cycles
• Noticeable air drafts around the dryer housing

This OEM LG part is also compatible with some Kenmore models.

This dryer duct assembly channels air from the drum to the blower and exhaust. Replacing a cracked or warped housing restores proper airflow, helps prevent lint bypass, and supports consistent drying performance.

• Directs and seals airflow between the drum and blower housing
• Helps maintain drying efficiency by minimizing leaks and lint bypass
• Damage or warping can lead to long dry times and reduced airflow
• Signs of failure include visible cracks, melted spots, or air/lint leakage around the duct area

• Disconnect power; for gas models, turn off the gas supply
• Access from the front by removing the top and front panel
• Note fastener locations and any attached brackets/harnesses, then transfer them to the new assembly
• Vacuum lint from internal ducting and verify seals before test run

For propane order 383EEL3002A.

The Cover, Lamp is an OEM part for LG dryers. This component covers and protects the interior lamp inside the dryer, ensuring it stays secure and free from damage while providing illumination inside the drum.

Over time, the lamp cover can become cracked or damaged due to the high temperatures and vibrations within the dryer. It is essential to replace a faulty lamp cover to maintain the proper lighting and protection for the lamp.

Symptoms of a bad lamp cover include:

• The interior lamp not staying in place
• Visible cracks or damage on the cover
• Reduced or blocked light inside the dryer drum
• The cover falling off or becoming loose

This OEM LG part is also compatible with Sears/Kenmore models.

This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.

• Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
• Sends temperature feedback to the control to regulate the heater or gas valve
• Failure can cause no heat, overheating, or erratic temperatures
• May lead to long dry times, short cycles, or temperature-related error codes

• Disconnect power and, for gas models, shut off the gas supply before servicing
• Access the sensor on the blower housing or exhaust duct; location varies by model
• Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
• Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow

This replacement lint filter fits in the dryer's lint trap to catch lint and fibers from each load. Replacing a torn or warped screen helps maintain airflow, improves drying performance, and keeps lint from circulating back onto clothes.

• Traps lint and debris drawn through the lint trap during drying
• Helps maintain proper airflow and protect the blower and vent path
• Replace if the mesh is torn, the frame is cracked/warped, or it won't stay seated
• Common symptoms: longer dry times, excessive lint on clothing or in the drum, difficulty inserting/removing the filter

• Disconnect power to the dryer before servicing
• Lift out the old filter and vacuum lint from the chute and surrounding area
• Install the new filter fully seated and flush in the opening; do not run the dryer without a filter
• Clean the lint screen before each cycle; check external venting if dry times remain long