Lg Refrigerator Parts

I've been down this road before with built in ice makers. Doesn't matter the brand. If they go just replace it. Don't bother with a service technician bill to boot. Very simple plug in replacement. Start to finish 10 minutes. Read more

Replaced door gaskets with new ones Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more

After several wrong size shelves was order from other companies. I came across Appliance Parts. The way your helped to find your needed part is in A category on its on compared to the other companies but to make a long story short. The PART arrived in A few short days and was the perfect fit. You definitely have a repeat customer here!!!!???? Read more

Removed and replaced the compressor start relay. Read more

• Fridge too warm

Replaced the Thermistor Assembly and also picked up Overload Protection circuit per the comments posted by the "experts" on the web site. Both parts cheap enough. I ordered parts at 3:30 in the afternoon and they showed up the next morning from half way across the country. Outstanding service. It also fixed the 9 year old refrigerator. Replacing the parts took about a half hour most of which was moving the unit from the wall and removing the panel to get at the parts. Read more

• Fridge too cold
• Fridge too warm

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

Ordered a new compressor and repaired by 3rd party. Read more

• Doesn't shut off
• Fridge too warm
• Noisy

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more

Ordered new tube part AJR56656503 for Lg LFX25978ST/01 watched a lot of videos but none showed how to remove the door tube end from its connection so I just cut and spliced the new tube to the old under the cover for the door hinge area after feeding it from the back of frig to that area. It was easy till I tried to remove the line end from ice maker area. Read more

Replaced plastic housing for $100. Recommend buying the whole assembly though. Cost a bit more but you would be done in 15min. When you just replace the housing, you have to disassemble the old one very carefully to reuse several parts that do not come with the housing. A lot of fragile plastics. Plus, make sure you have GooGone and 3M thin tape handy; you will absolutely need it. Again, buy the whole assembly and save time and headache. Read more

Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more

• Leaking
• Not dispensing water

Installed a new water valve assembly and a new ice maker assembly. Read more

• Ice maker not making ice
• Leaking

Replaced inlet water valve Read more

1. Googled "appliance replacement parts" - found two sites to consider 2. Researched parts needed via a exploded diagram - can't fix it if you can't name it. 3. AppliancePartsPros.com had the easiest diagram and after checking, the lowest price. 4. Parts showed up within a couple of days - an in-transit note was helpful. 5. The part screws in but watch out you don't break the tiny black pin holding the part on in addition to the screw. Needed JB Weld to fix that. Read more