Lg Washer Parts

Supports and centers the inner tub in front-load washers. Replace if cracked, corroded, or broken to restore proper drum alignment and balance.

This rotor assembly is the rotating half of your washer's direct-drive motor. It mounts to the rear of the tub and, working with the stator, spins the drum for wash and spin cycles to restore smooth operation.

• Couples with the stator to drive the inner tub during wash and spin
• Helps resolve no- or slow-spin complaints
• Can address a drum that won't turn or turns intermittently
• May reduce grinding/clicking from the rear caused by damaged rotor magnets

• Unplug the washer and turn off water supply before servicing
• Access from the rear; remove the center bolt and pull the rotor straight off the shaft
• Magnets are strong—keep fingers clear; align splines/keyway on reinstallation
• Tighten the center bolt securely and inspect the stator and sensor while open

Washer won't spin or shows LE error? A faulty stator assembly stops the motor from turning the drum. Moderate DIY repair restores spin and agitation.

Fix PE error codes and water overfilling issues with this pressure switch. Monitors tub water level to control fill and drain cycles. 30-minute DIY repair.

Shipping bolt for laundry centers and washers. Secures the drum during transport. Replace if lost, damaged, or missing after installation or moving.

This is a rubber gasket that seals the washing machine tub to prevent water from leaking during wash and spin cycles. It fits around the tub opening and maintains a watertight barrier. Replace this seal if you notice water leaking from around the tub area, or if the gasket appears cracked, hardened, or deformed.

Washer won't switch cycles or hums during agitation? The clutch and housing assembly connects the motor to enable spin cycles. Moderately difficult repair.

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Shipping bolt for laundry center and washer installations. Secures internal components during transport. Replace if bolt is missing, stripped, or damaged.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

Fix TE error code on your washer with this thermistor temperature sensor. Restores accurate temperature sensing and reliable cycle control.

Joins your washer's water line to internal plumbing with a secure, leak-resistant connection. Replace this connector if cracked, worn, or leaking.

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

Washer door won't stay closed or latch properly? This door latch hook secures your washer door, preventing accidental openings during cycles. Quick DIY fix.

Connects the washer's inner drum to the drive assembly. Replace if cracked, damaged, or worn to restore drum stability and eliminate wobbling or noise.

Replaces cracked, corroded, or broken inner drum assembly in your washer. Includes perforated basket, spider support, and lifters as one unit.