Lg Washer Parts

Secures the spider assembly to the inner drum in your washer. Replace if bolt is stripped, loose, or missing to restore secure mounting and reduce noise.

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

Replacement cover cap for washers. Conceals exposed screw heads and fastener holes for a clean finish. Install when original cap is cracked or missing.

Mounts inside the washer drum to lift and tumble clothes during the wash cycle. Replace if cracked, broken, or missing to restore proper agitation.

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

This is a flexible rubber bellows that connects the dryer exhaust outlet to the external vent duct on a combination washer/dryer unit. It channels hot, moist air out of the dryer section and helps absorb vibration during operation. Replace this bellows if it is cracked, torn, or collapsed, which can cause poor drying performance, excessive lint buildup, or moisture leaking inside the unit.

This is a door hinge for a front-load washing machine. It attaches the door to the machine's front panel, allowing it to open and close securely. Replace this hinge if the washer door is sagging, not closing properly, or if the hinge pin or mounting points are worn or broken.

Restores interior drum lighting for better visibility when loading and unloading laundry. Replace when light fails or dims to clearly see items in tub.

Heater assembly for washer dryer combos. Installs in the drying system to generate heat. Replace if cracked, corroded, or damaged to restore proper drying.

This is the start button assembly that initiates the dryer cycle when pressed. It connects to the control panel and engages the dryer's motor circuit. Replace this button if it is stuck, broken, feels loose when pressed, or the dryer does not start when you push it.

This washer shock absorber mounts between the outer tub and base to control movement during spin. Replacing a worn damper restores stability, reduces vibration and noise, and helps prevent the machine from walking or banging.

• Stabilizes the tub during spin by absorbing and controlling movement
• Reduces vibration and cabinet noise for smoother operation
• Helps the washer reach and maintain proper spin speed
• Worn shocks can cause shaking, banging, or walking during spin

• Disconnect power and water; use gloves and protect the floor.
• Access from the front or rear depending on model; remove panels as needed.
• Support the tub, then remove fasteners at both ends; install the new damper in the same orientation and tighten securely.
• Reassemble, level the washer, and run a test spin to check for vibration.

Secures the leveling foot to the washer base. Replace if cracked, stripped, or missing to restore a solid mounting point for proper leveling and stability.

Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.

Seals the gap between washer tub and door opening to prevent leaks. Replace if torn, cracked, or deformed to restore watertight seal. Verify fit.

If your washer fills slowly, overfills, or fills when off, the water inlet valve may need replacement. Simple DIY repair that stops leaks fast.

Washer won't start or runs intermittently? A faulty wiring harness disrupts power flow between components. This repair restores connections in 20-30 minutes.