Parts for Electrolux EW30EW65PSD: 04 - Lower Oven Parts

This seal creates a watertight barrier at a critical joint inside the dishwasher. Replacing a flattened, cracked, or missing seal helps stop leaks during the cycle and protects surrounding components from moisture. What it does:

• Maintains a watertight seal between mating parts in the wash system
• Helps prevent drips and pooling water under or around the appliance
• Restores proper sealing after wear, hardening, or deformation
• Common signs include leaks during a cycle, moisture beneath the unit, or visible wear on the old seal

• 1 seal

• Disconnect power and shut off the water supply before servicing
• Access the sealed area per your model's service information; remove the old seal
• Clean the groove/mating surfaces; seat the new seal evenly without twisting or stretching
• Restore power and water, then run a short cycle to check for leaks

Oven not responding to buttons or features won't activate? This control switch restores reliable operation by opening and closing electrical circuits.

The Range Lamp Assembly is an OEM part for Frigidaire stoves and ranges. It consists of the halogen light bulb, lens cover, and wiring harness necessary to illuminate the oven cavity. This lamp assembly provides light to the cooking and baking space, making it easier to view food and monitor cooking progress.  

Symptoms of a bad range lamp assembly include:

• The oven light not turning on at all  
• Dim, flickering, or intermittent light
• Burned out or blown light bulb
• Cracks or damage to the lens cover

Causes of failure can be a burned out light bulb, broken wiring, or damage from impact or heat over time. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Oven won't reach or hold set temperature? A faulty temperature sensor causes inaccurate heating. This monitor probe ensures consistent cooking results.

Replace your oven temperature probe if your meat thermometer feature isn't working or gives inaccurate readings. Simple plug-in installation in minutes.

Replace your damaged or worn wall oven control panel. This cosmetic panel covers the control area and installs on the front of your appliance unit.

Insulation for wall ovens. Installs between oven cavity and outer cabinet. Replace if damaged, compressed, or missing to restore heat retention.

Shield component for wall ovens and microwave combos. Replaces damaged, cracked, or missing shields. Installs inside the unit for protection.

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

If your oven won't heat or heats unevenly, this heating element restores proper temperature control. Straightforward DIY fix for most ranges.

The Bake Element is an OEM component for Frigidaire wall ovens. It is an integrated heating coil that generates heat through electric resistance when powered. Located near the bottom of the oven cavity, the bake element facilitates heating for various cooking functions like baking, roasting, or warming. This element measures approximately 13 x 11 inches.

Symptoms of a bad bake element include:

• Oven failing to reach or maintain desired cooking temperatures
• Bake cycles taking excessively long periods of time
• Hot or cold spots developing inside oven cavities
• Error codes appearing related to upper heating issues

Causes can be cracks in ceramic sheathing allowing arcing, or mineral deposits coating coils over extended use impeding heat transfer.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Heat shield for ranges and wall ovens. Protects internal components from excessive heat. Replace if cracked, warped, or damaged to prevent overheating.

Replace a cracked, damaged, or missing shield in your wall oven or microwave combo. This protective panel installs behind components to prevent wear.

Internal shield for wall ovens and microwave combos. Replaces damaged, cracked, or missing shields. Installs inside the unit for proper protection.

Receptacle block for electric ranges and wall ovens. Mounts in the rear panel to provide electrical connection. Replace if cracked, melted, or damaged.

Decorative trim piece that fits along the door edge of your electric wall oven. Replace if cracked, chipped, discolored, or missing to restore appearance.

Replacement mounting bracket that secures internal oven components. Install when original is cracked, bent, or missing to restore proper alignment and support.

This console cover replaces a damaged or worn dispenser trim to restore a clean, finished look and protect internal dispenser components from spills and debris. It helps maintain dispenser function and appearance. What it does

• Covers and protects dispenser/console components from moisture, food, and everyday wear
• Restores a flush, finished appearance to the dispenser area
• Prevents debris from entering control openings and trim seams
• Can reduce rattles or movement caused by a broken or loose trim piece

• One console cover (trim) as pictured

• Disconnect power to the refrigerator before beginning any work
• Remove any screws or retainers holding the old cover; keep hardware if reusing is intended
• Align the replacement cover carefully and secure with original screws or clips

Loud grinding or rattling from your oven? A damaged convection fan blade disrupts airflow. This replacement restores quiet operation in 20-30 minutes.

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

Oven won't heat after self-cleaning? This high-limit thermostat cuts power when temperatures get too high. Moderately easy DIY repair fix.

A replacement evaporator fan motor that circulates cold air across the evaporator and through the fresh food and freezer compartments to help maintain even temperatures and consistent cooling performance. What it does:

• Powers the evaporator fan to move cold air through the refrigerator and freezer.
• Restores airflow when a failed fan motor causes uneven cooling or warm spots.
• Stops continuous frost build-up on the evaporator caused by poor or no airflow.
• Eliminates loud grinding, buzzing, or rattling noises coming from the freezer area.

• Disconnect power to the appliance before attempting any repair to avoid electrical shock.
• Access typically requires removing interior panels or the evaporator cover; keep track of screws and clips.
• Handle the fan blade carefully and test operation after restoring power.

Reinforces and supports oven door glass panels. Replace if original stiffener is bent, cracked, or missing to properly secure glass in the door frame.

Burner won't heat or heats unevenly? This radiant cooktop surface element restores direct heat to one burner, returning reliable cooking performance.

Positions and supports range components to maintain proper alignment. Replace if cracked, broken, or missing to prevent rubbing and ensure panels fit correctly.

Replacement water-line tube that routes water inside the refrigerator to the ice maker or dispenser, helping restore proper water flow and reduce leaks. Designed to match factory routing so the line fits and seals correctly at the connections. What it does:

• Carries water from the cabinet valve to the ice maker or dispenser.
• Restores normal dispenser flow and ice production when the tube is cracked, pinched, or clogged.
• Helps stop visible leaks or pooling caused by damaged or misrouted tubing.
• Matches factory bends for correct routing and clearance behind panels.

• Disconnect power and shut off the water supply before starting any work.
• Remove shelves or panels as needed for access; watch for sharp edges.
• Check and replace any worn clamps or fittings; tighten connections and test for leaks with water on before reassembling.

Wiring harness for wall ovens. Connects electrical components inside the oven cavity. Replace if wires are frayed, burned, or connections are loose.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

Fix intermittent or failed component operation with this wiring harness assembly. Restores reliable electrical connections between range components.

Mounting screw for electric and gas ranges. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

This harness assembly is the appliance wiring connector bundle that carries power and signals between controls and components, restoring proper electrical connections for normal operation. What it does:

• Routes power and control signals between the control board and key components
• Replaces damaged, burned, or loose wiring that can cause intermittent operation
• Helps resolve symptoms like unresponsive controls, failure to start, or component loss of power
• Restores factory wiring layout and connector fit for reliable connections

• Disconnect power before starting; confirm power is off at the breaker
• Compare connectors and wire colors to the old harness before removal
• Route and secure harness to avoid heat or pinch points; use existing clips/mounts

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Illuminates your oven interior for visibility while cooking and cleaning. Replace when burned out to restore lighting. Verify fit with your model number.

Restores bright interior lighting so you can monitor cooking without opening the door. Replace when bulb is dim, flickering, or burned out. Confirm fit.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.