Need Help?
Call or text
Broil element burnt out or not heating? This top heating element provides intense direct heat for broiling. Takes 15-20 minutes to replace yourself.
Ordered a new part. Watched a YouTube video. Fixed it in 15 minutes. Knowing you need to stop the connectors from slipping into the back of the oven was the key. I used paperclips to stop the wires falling through the hole. Easy as ... Read more
Drip pan installs under range burners to catch spills and grease. Replace if cracked, warped, corroded, or heavily stained for a clean cooktop.
Ordered new drip pans from Appliance Parts Pros, hoping they'd fit perfectly...and THEY DID! We are so happy with them. The ones at other places didn't. Read more
Fix a burner stuck on high or an indicator light that won't turn off. This infinite switch controls heat settings on electric range burners. DIY-friendly repair.
1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more
Oven not heating or heating slowly? The bake element at the bottom of your oven cavity supplies heat for baking. Simple 2-screw, 2-wire repair.
I'm a 66 year old woman (on a fixed income) and I'd never before repaired an oven bake element . My stove is 20 years old but I still found it was much more affordable to change the bake element rather than buying a new stove. I called the number on the website and talked to a very informative woman. She answered all the questions I had about my stove. She told me about the repair video on the website which had step-by-step instructions. I ordered a new element - received it within 4 days.... Read more
Burners won't light? No spark on any burners? The spark module generates sparks to ignite gas burners. Easy DIY repair—usually takes under 30 minutes.
Replaced srark module Read more
Replace your range oven door gasket when torn or worn to restore an airtight seal and improve heating efficiency. Easy 5-15 minute install. Confirm fit.
I watched your video, knew that it would be a simple repair, ordered it, and did exactly what was shown in the video. It was crazy easy! 2 minutes start to finish! Easiest repair I've ever done. Read more
Seals oven door to prevent heat loss and improve cooking efficiency. Replace when brittle, frayed, or not sealing properly. Verify fit by model number.
First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more
Fix a burner that won't heat or has a charred connection. Burner receptacle replacement requires wire cutting, stripping, and splicing—about 30 minutes.
Followed the instructions that came with the replacement part: made sure stove top was unpowered, unscrewed the old housing from the stove top, cut the wires, stripped some insulation off, attached the new wires with the (accompanying) wire nuts, attached new housing to stove top. Read more
Burner won't light or spark? This top burner igniter creates the spark to ignite gas on your stovetop. Easy DIY repair in under 5 minutes with a screwdriver.
After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more
Metal hinge assembly that mounts to the oven door frame, enabling smooth opening and closing. Replace if cracked, broken, or no longer holding door securely.
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more
Burner not heating or 'Hot Surface' light stays on? This electric cooktop surface element is likely the fix. DIY-friendly, most installs take 15 minutes.
Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more
Replacement inner door glass panel for oven doors. Installs between outer glass and oven cavity. Needed when glass is cracked, broken, or shattered.
DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more
Replace a burner that won't heat or heats unevenly. This 8-inch surface element restores proper cooking temperature. Easy DIY repair in minutes.
Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more
Burner won't heat or cycles on and off? This infinite switch controls temperature levels on electric range surface elements. DIY repair in 10 minutes.
I ordered the correct part from AppliancePartsPros.com. When I received it, I opened the package and identified the parts I would need for my application. I cleaned up around my work space, then turned the power off to the appliance. I removed all the burners to get to the mounting screws for the range top. I then lifted the range top and supported it so I could see what I was working on . I first inspected all the wiring for breaks, or fraying. Then I moved on to the switch. Two screws... Read more
Broil element not heating or broken? This part provides intense radiant heat for broiling. Straightforward DIY replacement takes about 15-20 minutes.
I had the choice of spending $2K on another double oven stove or $60 on two elements. (I felt more secure about replacing both bake and broil elements just in case the fire had damaged the bake element) It was an easy decision and quick replacement! Power was already off to the stove so I cleaned up the fire retardent mess. I even found easy instructions dismantling the oven door in order to clean the powder residue from between the glass. I then removed the rack and remaining old elements. I... Read more
Illuminates appliance interior. Replace when burned out or dimming. Verify wattage and base type match your model before ordering. Easy DIY fix.
Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more