Magic Chef Dryer Parts

This replacement igniter lights the gas burner in your range or wall oven, restoring reliable starts and consistent heat. Swap in a fresh igniter to resolve hard-to-light burners and no-heat situations so cooking cycles begin as they should. What it does:

• Provides the ignition source to light the bake or broil burner flame
• Helps ensure fast, consistent burner light-off at the start of a heat cycle
• Common symptoms of failure: no ignition/no heat, delayed or intermittent ignition, repeated clicking without flame, or a gas odor before light-off

• 1 igniter assembly

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool completely
• Note wire connections and mounting orientation from the original part for correct reassembly
• Handle the ceramic/element carefully to avoid damage
• After installation, restore gas and power, then check for leaks with a soap solution

The Thermal Fuse is an OEM part for Whirlpool dryers. This part prevents the dryer from overheating by cutting off power to the heating element if the dryer exceeds a safe temperature. It helps protect the appliance and home from potential fire hazards caused by overheating.

Causes of a bad thermal fuse can include lint buildup restricting airflow, a malfunctioning thermostat, or excessive load causing the dryer to overheat.  

Symptoms of a bad thermal fuse include:

• Dryer not starting
• Dryer not producing heat
• Dryer shutting off mid-cycle
• No power to the dryer despite other electrical components functioning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Kit contains 2 pads, 1 right glide, 1 left glide, and instruction sheet. Support brace no longer included.

Sturdy metal door strike that mates with the latch/lock on your machine's cabinet. It keeps the door closed and engages the door switch so cycles can start and run without nuisance stops.

• Interfaces with the door latch/lock mechanism to secure closure
• Engages the door switch/interlock so the appliance can start and continue running
• Restores proper door alignment and latch feel after wear or bending
• Typical symptoms: door won't latch or pops open; unit won't start/run; intermittent stopping mid-cycle; visible damage to the strike

• Unplug the appliance (and shut off gas to gas dryers) before servicing
• Remove the existing strike and retain mounting hardware; note orientation
• Install the new strike in the same position; tighten screws and verify alignment
• Close the door to confirm smooth latching and proper operation

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

This dryer exhaust fan is used on many Admiral, Crosley, Hoover, Magic Chef, Maytag, Montgomery Ward and Norge brands. Size: 3-1/8 inches deep, 8 inch fin diameter, 7-1/8 inch hub diameter, 20 standard fins, 1/2 inch diameter motor shaft, 7/16 inch motor shaft diameter to flat side of shaft. Blower wheel clamp not included. For the clamp order WP312967.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This cycling thermostat regulates on/off heat cycles to maintain consistent operating temperature. Replacing a failed thermostat restores proper temperature control and helps protect the appliance from overheating or underheating during normal operation.

• Senses internal temperature and opens/closes contacts to control the heating circuit
• Helps prevent overheating; supports stable, repeatable heat cycling
• Common failure symptoms include no heat, overheating/shutting off too soon, or longer-than-normal run times
• Electrical component—failure may be intermittent before complete loss of function

• Disconnect power (and gas supply, if applicable) before service
• Note wire locations; transfer connectors one at a time to the new thermostat
• Mount firmly against the mating surface for accurate temperature sensing
• After installation, verify proper operation and temperature cycling

Built for electric dryers that require a 240V heater, this complete heater assembly restores proper heat output. Replace a burned-out element to resolve no-heat or weak-heat complaints and return your dryer to consistent, efficient drying.

• Generates the hot air needed to dry laundry during the cycle
• Typical failure symptoms: drum turns but no heat, longer dry times, or intermittent heating
• Can be checked with a continuity test; a broken or grounded coil indicates replacement is needed
• Factory-style 240V configuration for proper operation on compatible models

• Disconnect power at the breaker before servicing
• Access the heater per your model's service procedure and document wire locations
• Move wires to matching terminals; transfer any attached brackets/sensors from the old assembly if your model uses them
• Clear lint and verify airflow before a test run to confirm proper heating and cycling

This indicator light lens covers the pilot/indicator lamp opening on the appliance's control panel. It protects the assembly and diffuses the light so operating status is easy to see, restoring a clean, finished appearance when the original lens is damaged or missing.

• Covers and protects the indicator/pilot light opening in the panel
• Diffuses light for clearer visibility of the status indicator
• Helps keep dust, grease, and moisture out of the indicator assembly
• Common symptoms: lens cracked, missing, loose, or discolored; indicator light difficult to see

• Disconnect power to the appliance before servicing.
• Access the rear of the control panel/backguard to reach the lens area.
• Release the old lens from the panel opening and press the new lens in until fully seated; do not force brittle plastics.
• Reassemble panels, restore power, and verify the indicator is clearly visible.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement idler pulley keeps the drive belt tight and tracking correctly so the drum can rotate smoothly. It restores quiet, consistent operation when the original pulley is worn or seized and causing belt slippage or noise.

• Maintains proper tension on the drive belt to enable smooth drum rotation
• Provides a low-friction surface for the belt to ride on and stay aligned
• Common symptoms of failure: squealing/chirping, belt fraying or coming off, burning rubber smell, or a drum that won't turn
• Replace if the pulley wobbles, binds, or the rim/bearing is worn

• Disconnect power; if gas, shut off the gas supply
• Note belt routing, relieve tension from the idler arm, and remove the belt from the motor pulley
• Remove the retaining hardware from the old pulley, install the new pulley on the idler arm shaft, and re-tension the belt
• Manually rotate the drum to verify smooth belt tracking before reassembly and test run

This idler assembly is the spring-loaded belt tensioner that keeps the drive belt correctly tightened. Replacing a worn or seized idler restores smooth belt tracking, reduces squeal, and helps prevent slippage or loss of drive.

• Maintains proper tension on the drive belt for reliable power transfer
• Helps prevent belt slippage, squealing, or the belt coming off the pulleys
• Supports smooth rotation of the driven components
• Failure symptoms can include noise from the belt path, a frayed or derailed belt, or loss of motion

• Disconnect power and allow all moving parts to stop before servicing
• Access the belt path; relieve belt tension and remove the old idler assembly
• Install the new assembly; ensure the pulley spins freely and the belt is centered in the groove
• Manually rotate the system to verify alignment and clearances before restoring power

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity