Maytag Dishwasher Hose Or Tube

Connects the dishwasher sump outlet to the drain hose. Replace if cracked, leaking, or if the internal flapper valve is warped and no longer sealing.

Contains two, six foot long braided hoses with 90 degree ends.

Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.

Replacement water supply hose for dishwashers. Connects household water line to the dishwasher inlet. Replace if cracked, leaking, or damaged.

Size: 7 foot long.

Routes wastewater from your dishwasher pump to the home drain. Replace if cracked, kinked, punctured, or worn to restore proper drainage and prevent leaks.

Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.

Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.

Water line kit for connecting ice makers to household water supply. Includes copper tubing, valve, and fittings for installation under kitchen sink.

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

5 foot. Package of 2.

This fill and drain hose assembly routes water into and out of the washer, helping the machine fill, drain and operate normally. Replacing a worn or damaged hose prevents leaks and restores reliable water flow. What it does

• Carries incoming water to the washer tub during the fill cycle.
• Provides a path for water to exit during drain/spin cycles.
• Commonly replaced for visible cracks, pinholes, leaks, or kinking that restricts flow.
• Can resolve symptoms like water on the floor, poor filling, or incomplete draining.

• Turn off power and shut off water supply before beginning work.
• Inspect hose routing and fasteners; replace any damaged clamps or connectors.
• Tighten connections securely and test for leaks at low flow before a full cycle.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

Hose assembly for portable dishwashers. Connects your unit to the sink faucet for water supply. Replace if cracked, leaking, or stripped threads.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A