Maytag Dishwasher Pump

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Volute with Seal is an OEM part for Whirlpool dishwashers. This part directs water flow within the dishwasher's pump, ensuring efficient circulation and pressure during the wash cycle. The seal helps to prevent leaks by maintaining a tight closure between the volute and other pump components.

Common causes of a bad volute with seal include wear and tear from regular use, damage from debris or hard water deposits, and seal degradation due to age or chemical exposure.

Symptoms of a bad Volute with Seal include:

• Water leaking from the pump area
• Decreased washing performance
• Unusual noises from the pump during operation
• Visible cracks or damage to the volute or seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

This drain impeller assembly circulates and ejects wash water through the washer's drain pump, restoring proper drainage and helping prevent standing water after a cycle. Durable design fits into the pump housing for reliable performance. What it does:

• Presses water through the pump housing to enable normal draining during drain/spin cycles
• Replaces worn or damaged impeller vanes that can cause slow or no draining
• Helps reduce noise and vibration from an imbalanced or broken impeller
• Restores proper water flow when the pump motor runs but little or no water is expelled

• Disconnect power and water supply before starting any repair
• Access requires removing the washer cabinet or pump housing depending on model
• Inspect pump housing and sealing surfaces for damage or debris before installing the new impeller
• Use common hand tools; tighten fasteners to OEM torque specs where provided

This part is a pump and motor assembly. This component is made for use on dishwashers and is responsible for pumping water through the spray arms during the washing cycle. This part is essential for the operation of the appliance. If there is no water circulation during the dishwashing cycle, then the pump and motor assembly will need to be replaced. The spray arms spin during the washing process and this assembly causes the arms to spin, so if they are not spinning, this will be the correct replacement part. It is advised that the person performing the repair unplug the dishwasher from the electrical outlet or turn off the house circuit breaker for the dishwasher before attempting to replace this part. This particular pump and motor assembly is compatible with dishwashers that are manufactured by the Whirlpool, Kenmore, and Jenn-Air brands. It is sourced directly from the manufacturer and is sold individually.

Seal not included