Maytag Dryer Axle, Roller, Pulley Parts

The Idler Pulley Assembly is an OEM part for Whirlpool dryers. This component is essential for maintaining the proper tension on the dryer belt, allowing the drum to rotate smoothly during drying cycles.

Over time, the idler pulley assembly can wear out or become damaged due to the constant movement and tension it endures. Common causes of a bad idler pulley assembly include regular wear and tear, accumulation of lint or debris, or excessive strain from overloading the dryer.

Symptoms of a bad idler pulley assembly include:

• Squeaking or squealing noises during dryer operation
• The drum failing to rotate or rotating unevenly
• The dryer stopping unexpectedly mid-cycle
• The belt slipping or breaking

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Front Drum Roller Shaft is an OEM part for Whirlpool dryers. This component provides support and stability to the drum while it rotates, ensuring smooth and quiet operation during the drying cycle. The roller shaft works in conjunction with the drum rollers to maintain proper alignment and reduce friction.

Over time, the front drum roller shaft can wear out or become damaged due to continuous use and the constant movement of the drum. Factors such as heavy loads, misalignment, and lack of lubrication can contribute to the deterioration of the shaft.

Symptoms of a bad front drum roller shaft include:

• Squeaking or grinding noises during the drying cycle
• The drum not rotating smoothly
• Increased friction or resistance when turning the drum by hand
• Uneven or excessive wear on the drum rollers

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Idler Pulley Arm is an OEM component specifically designed for Whirlpool brand clothes dryers. It pivots to lift belt tension and remove slack during dryer tumbling.  

Symptoms of a problematic idler pulley arm include:

• Drive belt slips off pulleys or tracks improperly
• Reduced drying due to inefficient tumbling  

Potential causes involve typical wear from extended usage. Seizing bushings or restrictive movement may diminish functionality over time as well.

This genuine OEM Whirlpool part is compatible with models including some brands produced by KitchenAid, Maytag, and Kenmore.

The Idler Pulley Arm is an OEM replacement part for Whirlpool dryers. As a connecting part, it works to route the drive belt and suspend the idler pulley. Mounted on a pivoting bracket, the durable arm positions the idler pulley to maintain proper belt tension over the lifter roll and drum.

Causes of a bad idler pulley arm can include fatigue from extended use, damage from overtightened belts, or broken welds impairing motion.

Symptoms of a bad idler pulley arm include:

• Slipping or prematurely worn drive belts
• Reduced or inconsistent drum rotation
• Grating noises or abnormal vibrations during use

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

The Drum Roller Axle is an OEM replacement part for Whirlpool dryers. It is the component that attaches to the rear panel and supports the dryer drum rollers.

Causes of a bad drum roller axle can include wear from years of operation, potentially leading to bending or wobbling that disturbs smooth drum spinning. Bearing seals may also deteriorate through continuous motion and heat exposure.

Symptoms of a bad Drum Roller Axle include:

• Vibrations or imbalanced drum rotations sensed during drying
• Premature failure of other drum or suspension components
• Reduced efficiency as uneven tumbling hinders fabric agitation
• Noises and rattling sounds from within the dryer cylinder area

This OEM Whirlpool part is also compatible with Maytag, Jenn-Air, Amana, and select Kenmore models

For complete assembly for easier installation order WP37001287

This replacement idler pulley keeps the drive belt tight and tracking correctly so the drum can rotate smoothly. It restores quiet, consistent operation when the original pulley is worn or seized and causing belt slippage or noise.

• Maintains proper tension on the drive belt to enable smooth drum rotation
• Provides a low-friction surface for the belt to ride on and stay aligned
• Common symptoms of failure: squealing/chirping, belt fraying or coming off, burning rubber smell, or a drum that won't turn
• Replace if the pulley wobbles, binds, or the rim/bearing is worn

• Disconnect power; if gas, shut off the gas supply
• Note belt routing, relieve tension from the idler arm, and remove the belt from the motor pulley
• Remove the retaining hardware from the old pulley, install the new pulley on the idler arm shaft, and re-tension the belt
• Manually rotate the drum to verify smooth belt tracking before reassembly and test run

This idler assembly is the spring-loaded belt tensioner that keeps the drive belt correctly tightened. Replacing a worn or seized idler restores smooth belt tracking, reduces squeal, and helps prevent slippage or loss of drive.

• Maintains proper tension on the drive belt for reliable power transfer
• Helps prevent belt slippage, squealing, or the belt coming off the pulleys
• Supports smooth rotation of the driven components
• Failure symptoms can include noise from the belt path, a frayed or derailed belt, or loss of motion

• Disconnect power and allow all moving parts to stop before servicing
• Access the belt path; relieve belt tension and remove the old idler assembly
• Install the new assembly; ensure the pulley spins freely and the belt is centered in the groove
• Manually rotate the system to verify alignment and clearances before restoring power

This dryer drum support roller holds the drum on its axle and lets it rotate smoothly. Replacing a worn or noisy roller restores quiet, even tumbling and helps prevent belt strain and added wear on related parts.

• Supports the dryer drum and allows low-friction rotation on the shaft
• Helps keep the drum aligned and stable during cycles
• Wear can cause squeaking, thumping, rumbling, or grinding noises
• Flat spots, cracks, or excessive wobble indicate replacement

• Disconnect power; turn off gas supply for gas models
• Access the roller by removing the front or rear panel/bulkhead per model; relieve belt tension and support the drum
• Install the new roller on the existing shaft, reusing model-specific washers/clips as required
• Inspect remaining rollers, idler pulley, and belt; replace any worn parts together to maintain smooth, quiet operation

This motor drive pulley transfers power from the dryer motor to the drum belt so the drum spins smoothly. Replacing a worn pulley restores proper belt tracking and reduces noise for reliable drying performance. What it does:

• Guides and supports the drive belt so the drum turns freely
• Maintains correct belt alignment to prevent slipping or fraying
• Replaces noisy, cracked, or worn pulley surfaces that cause squealing
• Helps restore normal drum rotation when the belt skips or the drum won't turn

• Disconnect power before servicing to avoid injury
• Inspect the drive belt and idler for wear; replace if damaged
• Use basic hand tools; support the drum and follow the dryer's service manual

This rear support assembly stabilizes the appliance's rear housing and helps keep internal components aligned for smooth operation and reduced vibration. It restores proper rear-end support to prevent rubbing, noise, and uneven motion. What it does:

• Provides a stable mounting point for the appliance's rear section to maintain alignment
• Reduces vibration and rattling caused by a loose or worn rear support
• Helps prevent rubbing, scraping, or grinding noises from misaligned components
• Restores proper fit between the rear housing and moving parts to promote smooth operation

• One rear support assembly

• Disconnect power (and gas if applicable) before beginning any repair
• Access typically requires removing the appliance's rear panel or cabinet; follow OEM service manual steps
• Inspect surrounding mounting hardware and replace any worn fasteners for a secure fit

The Whirlpool Motor Pulley is an OEM part for Whirlpool clothes dryers. It is the component located on the dryer drum motor that transmits power to spin the dryer cylinder and tumble clothes during operation. It allows the belt to grip effectively for transmission of torque from the motor.

Symptoms of a bad Motor Pulley include:

• The dryer drum failing to spin and tumble clothes during cycles
• Abnormal squealing, grinding or belt slipping noises from inside the dryer
• Minimal air flow and prolonged drying times

Causes of failure can include cracks or deterioration of the pulley edge from prolonged use, the belt wearing grooves into the pulley, or loose mounting bolts allowing wobbling.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This motor drive pulley transfers motor torque to the dryer drum belt so the drum spins smoothly and reliably. Replaces a worn or damaged pulley to restore proper belt alignment and reduce noise or slipping. What it does:

• Guides the dryer drum belt so the belt tracks correctly and transmits motor power to the drum.
• Maintains belt alignment and tension to prevent slipping or uneven drum rotation.
• Reduces bearing or shaft wear that can cause squealing, grinding, or vibration.
• Helps restore normal drum rotation when a cracked or worn pulley prevents the drum from turning.

• One motor drive pulley (quantity: 1)

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Inspect belt, idler, and motor shaft for wear; replace damaged components as needed.
• Use basic hand tools; support the drum or bulkhead as required to access the pulley safely.

The Dryer Drum Roller Axle is an OEM part for Whirlpool dryers. It plays a role in the dryer's operation by offering support and an axis for the drum roller to spin smoothly. This guarantees effective and balanced tumbling of clothes throughout the drying cycle. 

Causes of a bad Dryer Drum Roller Axle can include prolonged use leading to wear and tear, accumulation of lint and debris causing additional friction, or improper loading of the dryer drum which can bend or strain the axle.

Symptoms of a bad Dryer Drum Roller Axle include:

• Unusual noises, such as squeaking or grinding, during the operation
• The dryer drum struggling to turn or not turning at all
• Increased vibration or shaking of the dryer unit
• Clothes taking longer to dry or not drying evenly

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.