Maytag Dryer Parts

This hinge guide is the small bushing the hinge pin rides in. It reduces friction and keeps the panel aligned so the door or lid opens smoothly and closes flush for reliable everyday use.

• Provides a low-friction bearing surface for the hinge pin
• Helps maintain door/lid alignment so it closes flush
• Wear can lead to sagging, scraping, squeaking, or binding
• Restores smooth operation and consistent closing when the original is worn

• Disconnect power; shut off water supply
• Support the door or lid before loosening hinge fasteners
• Remove the worn guide and install the new guide on the hinge pin or in the hinge bracket
• Reassemble, then check alignment and smooth open/close

Dryer won't power on or controls aren't responding? This control transformer converts line voltage to power timers, relays, and sensors. Moderate DIY repair.

This blower housing assembly replaces the blower chamber that supports the blower wheel and routes air through the dryer for proper tumbling and drying. Restores correct airflow and helps reduce overheating or poor drying performance. What it does:

• Houses and supports the blower wheel to direct airflow from the drum to the exhaust.
• Ensures proper airflow for consistent drying and venting.
• Can address symptoms like weak airflow, long dry times, or unusual blower noise when damaged or cracked.
• Works with the blower wheel and motor to maintain lint passage and exhaust flow.

• Disconnect power before inspecting or replacing the blower housing; follow manufacturer safety procedures.
• Access may require removing the dryer front or rear panel depending on model.
• Inspect the blower wheel and motor for damage or obstructions while replacing the housing.

Replace your damaged or worn dryer vent hose. This 5-foot flexible duct connects your dryer to the exterior vent, ensuring proper airflow and safety.

This LP gas conversion orifice adjusts gas flow for compatible gas ranges and cooktops when converting from natural gas to liquid propane, helping the appliance run safely and correctly after conversion. What it does:

• Replaces the burner orifice to reduce gas flow for LP fuel pressure and correct flame size
• Helps restore consistent, stable burner flames after an authorized LP conversion
• Addresses symptoms like unusually large or yellow flames, poor ignition, or unstable burner performance after conversion
• Works with the appliance's existing valve and burner components as part of a proper conversion

• Follow the appliance manufacturer's LP conversion instructions and parts list exactly
• Turn off gas supply and disconnect power before servicing
• Use correct torque and fittings; do not force or cross-thread the orifice
• Always perform an approved gas leak test and check burner flames after installation

Replace your dryer's damaged, dented, or cracked outer door panel. This finished surface panel installs on the front door assembly to restore appearance.

Replace your dryer's drum shaft bushing when you hear unusual noises during operation. This bearing supports smooth drum rotation and reduces friction.

This finished burner funnel directs gas and air into the burner for correct flame shape and ignition. It replaces a damaged or corroded funnel to help restore even heating and reliable burner performance. What it does:

• Channels gas and air into the burner for proper mixing and flame distribution
• Helps maintain even flame across the burner for consistent cooking heat
• Can reduce ignition delays or uneven flames caused by a damaged funnel
• Works with the burner assembly; not a standalone gas valve or igniter

• Turn off gas supply and electricity to the appliance before servicing
• Replace only with the correct funnel for your burner; follow OEM diagram for orientation
• Tighten fittings by hand-first, then snug—do not overtighten; inspect for leaks after reassembly

Replacement machine bolt for securing panels, brackets, and components in dishwashers, dryers, washers, and laundry centers. Restores fit if missing.

Right-angle wall elbow redirects your dryer vent through wall openings. Replace worn, damaged, or misaligned elbows to maintain secure exhaust alignment.

Secures hoses and prevents leaks in dryers, washers, and laundry centers. Replace when connections loosen or drips appear. Verify fit by model.

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

Adjustable leveling foot for dryers. Replaces worn, broken, or missing legs to stabilize your dryer and stop rocking on uneven floors.

Replacement door handle for dryer doors. Installs on the outer door panel. Needed when original handle is cracked, broken, loose, or missing.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

Dryer won't heat or shuts off too soon? This high-limit thermostat prevents overheating by cutting power when temps get too high. Easy DIY fix.