Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Microwave has no power or won't start? A faulty cavity thermostat often causes complete shutdowns. This part restores temperature control in 5-10 minutes.
I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more
Element not heating or glowing? This surface heating element restores heat to your cooktop burner. Moderate DIY repair requires glass top removal.
So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more
Replace your worn oven door gasket to restore a heat-resistant seal, stabilize temperature, and improve baking performance. Confirm fit with your model number.
Although I had difficulties finding the right part to order (never could find the model #s on the oven), somehow I found this part. It fits perfectly and was very easy to install. Thank you! Read more
Replacement door glass for ovens and ranges. Restores clear viewing window when original is cracked, shattered, or damaged. Fits between door panels.
Replaced glass panel. 4 screws on plate face, 2 on bottom. Read more
Brass seal creates a leak-resistant joint in range burner tube connections. Replace when deformed or worn during line service to ensure safe operation.
Flip the burner facing down. Take out the seven screws that hold together the housing and the slip off the housing. Disconnect the igniter leads. Turn the burner clock wise from the opposite side your likely working. You'll get a better purchase there. Take the screws out of the old igniter, as they don't come in with the new igniter. Install the new igniter on to the new burner. Make sure that the igniter is poking all the way out of the whole in the burner. I found that the screws did... Read more
Fix continuous clicking and burners that won't light. This spark electrode generates the arc that ignites gas burners. Simple DIY repair for most users.
Replacement thermostat knob for oven temperature control. Mounts on control shaft. Needed when original is cracked, stripped, worn, or missing numbers.
Went through some lengthy internet exchanges with an enormously patient person at Appliance Parts and after a couple of tries, complicated by an oven ID tag that was only partially legible, she was able to find the right dials and sent them promptly. The are installed and exactly what I needed. Read more
Fix burners that won't light or spark intermittently with a new surface burner igniter. Most DIYers complete this repair in 20 minutes with basic tools.
I disassembled the top of the range and looked at the problem burner. It looked like there was a spark at all three other burners but not the problem burner. There was a visible spark at the connector between the wiring harness and the ceramic igniter but that spark wasn't making it up to the top of the igniter where it can light the burner. I ordered a new igniter for $19 and it was on my doorstep the next day. I replaced the part and now my wife thinks I am a genius. Don't tell her that... Read more
Burner not heating? This radiant surface element restores heat output beneath your glass cooktop. Straightforward repair with basic tools.
Need to open because no parts’ numbers can be identified through their website. But the rest “order and put in” are very easy steps. Will come back if I do need other parts Read more
If your range has a strong burning smell or won't power on, the terminal block may be heat-damaged. This insulated connector restores safe power flow.
Replaced it with the part I got from you. Read more
This fan switch restores dependable control of your appliance's ventilation fan. It routes power to the blower motor so you can turn the fan on and off from the control panel when the original switch becomes worn or fails.
Cut off old bought new spades Read more
Replace a cracked, broken, or missing control knob on your electric range. This knob attaches to the control stem for selecting temperature settings.
Sits on sealed gas burners to shape the flame and protect the burner head. Replace when the original is cracked, warped, damaged, or missing.
I was able to contact AppliancePartsPro.com and was able to complete a one-stop-shop to correct my issues. This was not the first time using this company. They have the catalogs of parts and great descriptions. I have listed them as a favorite on my computer. Read more
Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.
Could not level stove. Front leveling legs had pieces broken out where leg contacted floor. Back leveling legs were worn and did not stay at corrected height when stove returned to full weight on floor. Replaced both front and back leveling legs, and stove was able to be leveled. Also bought Touchup Paint for numerous nicks and scratches - color matched perfectly. Read more
Oven won't heat or overheats? This thermostat monitors temperature and controls heating elements. Moderate DIY repair requires back panel removal.
Removed back panel and top burner cover to replace thermostat Read more
Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.
At first, I thought that it was the defrost timer, but when I took apart the freezer, I found that the evaporator fan motor wasn't running, so I replaced it. Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.