Maytag Refrigerator Drip Pan

The Dispenser Overflow Grille is an OEM part for Whirlpool refrigerators. It fits in the dispenser area and catches any spills or overflow from the water and ice dispenser, preventing them from dripping onto the floor or into the appliance.

You should replace the dispenser overflow grille if it becomes cracked, warped, or otherwise damaged. Causes of a bad overflow grille can include constant exposure to water, accidental impacts, or regular wear and tear over time.

Symptoms of a bad dispenser overflow grille include:

• Visible cracks or breaks in the grille
• Water pooling around the dispenser area
• The grille not fitting securely in place
• Difficulty in keeping the dispenser area clean

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Other colors:

• For Biscuit order WP2206670T.
• For white order WP2206670W.

The Drip Pan is an OEM part for Whirlpool refrigerators. Located beneath the refrigerator, it collects and holds water that drips from the defrost system, preventing it from leaking onto the floor.  

Causes of a bad drip pan can include cracks or holes from physical damage, warping from exposure to temperature fluctuations, or excessive buildup of dirt and mold.  

Symptoms of a bad drip pan include:

• Water pooling under the refrigerator
• Visible cracks, holes, or warping in the pan
• Mold or mildew growth in the pan
• Unpleasant odors emanating from the refrigerator base

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Stainless

This drip tray in a Midnight finish sits at the dispenser area to catch minor drips and splashes, helping keep your door clean and dry. It also refreshes appearance if the original tray is cracked, stained, or missing.

• Collects drips under the dispenser to help prevent water from running down the door or onto the floor
• Provides a stable landing for cups and glasses during dispensing
• Restores a clean look if the old tray is worn or discolored
• Typical symptoms: puddling at the dispenser, mineral buildup, or a loose/warped tray

• Pull the old tray straight out; some models require lifting the front edge first
• Clean the recess thoroughly before installing the new tray
• Align tabs and press evenly until fully seated—do not force
• Avoid activating the dispenser during installation; wipe with mild soap and water only

This dispenser drip tray sits in the door recess to catch drips and splashes during dispensing, helping keep the front of your refrigerator clean and reducing moisture that can run down the door onto surfaces below. What it does:

• Collects water droplets and minor spills in the dispenser area
• Helps reduce stains, residue, and corrosion around the dispenser opening
• Restores proper fit and appearance when the original tray is cracked, warped, or missing
• Common symptoms: water pooling in/under the dispenser, loose or ill-fitting tray, visible cracks or leaks

• 1 drip tray

• Unplug the refrigerator and shut off the water supply before servicing
• Lift out the old tray from the dispenser recess; clean and dry the area
• Align and press the new tray fully into place so it sits flat and secure
• Wipe away any remaining moisture before restoring power and water

Evaporator drip pan that collects defrost water and directs it to the drain, helping prevent leaks and puddles under the appliance. Restores proper drainage for reliable operation. What it does:

• Catches and channels defrost/condensate water away from the evaporator to prevent leaks beneath the unit.
• Helps stop water pooling or dripping from the bottom of the appliance.
• Reduces the risk of moisture-related odors or mildew by keeping drainage contained.
• Works with the refrigerator's drain system to promote normal defrost water flow.

• Disconnect power to the appliance before beginning any service.
• Access may require removing the toe grille or pulling the appliance out; follow the OEM service instructions for your model.
• Inspect and clear the drain tube and drain outlet while replacing the pan to ensure proper flow.
• Handle the pan carefully during installation and ensure it is seated so water flows into the drain as intended.

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Replacement drip tray in white that installs under the appliance to collect spills and direct water away from internal components, helping prevent damage and making cleanup easier. What it does:

• Catches leaks, drips and overflow to protect the cabinet and floor.
• Directs water away from controls and electrical components to reduce risk of damage.
• Replaces cracked, warped or discolored trays that no longer hold water.
• Helps limit staining and makes routine cleanup faster.

• Disconnect power to the appliance before starting any work.
• Access the tray by removing the lower access panel or kickplate as required for your model.
• Remove the old tray and slide or snap the replacement into place; avoid forcing parts.

This drip tray collects defrost and condensation water under the refrigerator to help prevent leaks and water pooling on the floor. It restores proper water capture and drainage for affected fridge models. What it does:

• Catches defrost and condensation runoff from the evaporator or drain system
• Helps prevent water pooling beneath the appliance and potential floor damage
• Works when original tray is cracked, warped, clogged, or missing
• Compatible with factory mounting points and drain alignment when the correct part is used

• One replacement drip tray

• Disconnect power before servicing to avoid electrical shock
• Access may require removing kick plate or lower front panel; follow your model's service instructions
• Slide or snap the tray into place and secure any retaining clips or screws removed earlier

This evaporator tray collects defrost and condensation water from the evaporator assembly to help prevent leaks and water pooling inside the refrigerator. It fits under the evaporator to route meltwater to the drain system. What it does:

• Catches and channels defrost/condensation water away from internal components
• Helps prevent water pooling or dripping inside the fresh food or freezer compartments
• Supports proper defrost drainage to reduce ice buildup around the evaporator
• Works with the drain tube and pan to direct water toward the drain and evaporator pan

• Disconnect power to the appliance before beginning service
• Access may require removing interior panels or the evaporator cover—handle evaporator fins and sensors with care
• Inspect and clear the drain tube and gasket while replacing the tray for optimal performance

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators. It is a plastic tray located below the ice and water dispenser that catches any accidental spills or drips during use. 

Symptoms of a bad drip tray can include:

• Ice or water accumulation under the dispenser area  
• Overflow or leakage onto surrounding counter surfaces
• Stains or moisture damage below the refrigerator

Causes of drip tray issues occur from cracks, punctures, or breakage rendering it unable to hold liquid. Normal wear over extended use may also cause trays to develop leaks.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, and Kenmore brands.

This drip tray collects defrost and condensation water under the refrigerator to prevent pooling and protect flooring. It fits beneath the cabinet and helps channel water to the drain so the fridge runs clean and dry. What it does:

• Captures and directs defrost/condensation water away from the cabinet bottom
• Prevents water from pooling under the appliance and reduces risk of floor damage
• Helps avoid musty smells by keeping moisture contained and draining properly
• Compatible replacement when original tray is cracked, warped, or leaking

• High-level replacement — typically accessed from the front kickplate or by pulling the fridge out slightly
• No special tools usually required; follow manufacturer instructions for safe removal and reinstallation
• Disconnect power to the appliance before working on it to avoid electrical hazards
• Inspect surrounding drain and seals while replacing to ensure proper operation

This drip pan is the replacement drain tray that catches defrost and condensation water to help prevent leaks and puddling under the appliance. It restores the unit's normal water collection and drainage path. What it does:

• Collects defrost and condensation water from the evaporator area.
• Directs water toward the drain channel to prevent pooling under the appliance.
• Helps reduce risk of water damage to flooring from leaks or overflow.
• Addresses symptoms like water puddling beneath the unit or visible drips.

• Designed for straightforward replacement; use appliance-specific service manual for exact procedure.
• Disconnect power (and water if applicable) before starting any service.
• Handle carefully to avoid bending tabs or damaging mounting locations.

This grille is the external vent trim that covers the appliance's lower air opening, restoring appearance and allowing proper airflow. It replaces cracked, broken, loose, or missing vent trim to keep the front of the appliance looking finished. What it does:

• Covers and protects the lower vent opening while allowing airflow through the front panel
• Restores a finished appearance when original grille is cracked, warped, or missing
• Helps maintain proper ventilation at the appliance base to support cooling components
• Secures into the cabinet openings using factory clips or screws

• One grille

• Disconnect power to the appliance before beginning repairs
• Installation typically requires removing the access panel or toe kick; retain all fasteners
• Align grille tabs with slots and press or screw into place without forcing to avoid breakage
• If clips are damaged, replace them to ensure a secure fit and prevent rattling

This replacement drip tray catches and channels condensation or small leaks to keep the area under your appliance dry and reduce the risk of water damage. It restores proper drainage and helps prevent pooling beneath the unit. What it does:

• Collects condensation and minor leaks to prevent water from reaching the floor or cabinet
• Directs water to the appliance's drain area so moisture evacuates properly
• Helps reduce odors and mold growth caused by standing water
• Common symptom fix: visible puddling or dampness beneath the appliance

• Disconnect power (and water, if applicable) before starting any repair
• Drain any standing water and work with towels to catch residual moisture
• Installation typically requires removing lower access panels or the kickplate; keep fasteners organized

This evaporator tray collects and channels defrost and condensation water away from the refrigerator evaporator, helping prevent leaks and ice buildup so the cooling system runs cleanly and reliably. What it does:

• Captures defrost and condensation water from the evaporator coil
• Directs water to the drain system to avoid pooling inside the cabinet
• Helps reduce ice buildup around the evaporator area
• Supports normal defrost operation and prevents water-related leaks or odors

• Disconnect power to the appliance before replacing parts to avoid electrical shock.
• Remove food and shelving as needed for safe access to the evaporator area.
• Inspect surrounding seals and drain tube for clogs or damage while replacing the tray.
• Handle carefully to avoid damaging delicate evaporator fins or nearby components.