Maytag Refrigerator Touch Pad

The Dispenser Overlay is an OEM part for Whirlpool refrigerators. It is a component that covers and protects the control panel and buttons of the dispenser on the fridge. It provides a protective barrier against dust, moisture, and every day wear and tear, helping to maintain the appearance and functionality of the dispenser.

Causes of a damaged or worn-out dispenser overlay can include regular use over time, accidental spills or scratches, or exposure to harsh cleaning chemicals. These factors can lead to a faded or unreadable display, a sticky or unresponsive touchpad, or an unattractive appearance.

Symptoms of a bad dispenser overlay may include:

• Faded or illegible display on the control panel
• Unresponsive or sticky buttons on the dispenser
• Visible damage, scratches, or discoloration on the overlay

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Restore reliable button response on your refrigerator's control panel. This control keypad registers your selections and sends them to the electronic control so features and settings respond consistently. What it does:

• Provides the button interface for the refrigerator's control panel
• Sends selection signals to the main control board
• Failure can cause dead or stuck buttons, erratic inputs, or no response
• Common symptoms include unresponsive controls, intermittent operation, or unintended changes

• 1 control keypad

• Disconnect power to the refrigerator before servicing
• Carefully remove the control panel/trim to access the keypad; avoid prying damage
• Note connector orientation and avoid creasing the flex cable; seat the connector fully
• Restore power and test all buttons before final reassembly

This electronic control board replaces the appliance's console control module to restore normal user interface and electronic function. It manages timed cycles, user inputs and sends signals to the main components for correct operation. What it does:

• Interprets button/knob inputs and runs selected cycles or modes
• Sends control signals to heating, motor, valve or compressor circuits as required
• Helps correct symptoms like unresponsive controls, failure to start, or erratic cycle behavior
• Replaces a failed or damaged console control to restore reliable electronic control

• One electronic control board

• Disconnect power before servicing to avoid shock or damage
• Handle the board by its edges and avoid touching components or connectors
• Verify connector locations and wire routing matches the original during reassembly

This dispenser facade replaces the outer trim pieces around your refrigerator's ice and water dispenser, restoring appearance and proper fit for smooth operation and sealing. It's a direct-fit cosmetic and protective assembly. What it does:

• Covers and protects the dispenser opening and controls from damage and debris
• Provides a finished look and helps direct water/ice into the cup
• Restores proper alignment when cracked, warped, or broken facade causes interference
• Helps prevent drafts and minor water splash at the dispenser area

• Disconnect power and shut off water to the appliance before servicing
• Many installations require removing the dispenser bezel and releasing snap-clips or screws; save hardware for reinstallation
• Handle plastic trim carefully to avoid scratches; use a soft pad when setting parts down

This replacement cover is a protective panel that helps shield internal components from dust and debris and restores the appliance's finished appearance. Installing the correct cover keeps parts protected and helps maintain safe, reliable operation. What it does:

• Protects internal electronics and wiring from dust, lint, and incidental contact
• Restores the appliance's exterior finish where the original cover was damaged or removed
• Helps prevent accidental access to moving or energized components
• Can reduce noise by covering openings near motors or fans

• One replacement cover

• Disconnect power to the appliance before beginning any work
• Handle edges carefully to avoid cuts and to prevent damage to the cover finish
• Verify orientation and fastener locations before tightening screws; do not overtighten

This front cover is the exterior cabinet panel that protects internal components and gives the appliance a finished appearance. It restores a clean, secure front and helps shield controls and openings from dust and debris. What it does:

• Replaces a worn, cracked, or damaged front cabinet panel to restore proper fit and appearance
• Protects internal parts and wiring from dust, moisture, and physical damage
• Helps maintain proper airflow and alignment of door or control openings
• Can reduce rattles or gaps caused by a damaged front panel

• One front cover as shown

• Inspect surrounding trim, fasteners, and mounting clips; replace any broken hardware for a secure fit
• Disconnect power to the appliance before beginning work and follow basic electrical safety
• Some models require partial disassembly of the console or outer cabinet; handle painted surfaces carefully to avoid scratches
• Verify correct orientation and alignment before tightening all fasteners