Maytag Refrigerator Gasket & Seal

This replacement door gasket creates an airtight seal around the refrigerator door to help keep cold air in and reduce frost buildup. It restores proper sealing to improve cooling consistency and energy efficiency. What it does:

• Seals the door edge to prevent cold air loss and reduce moisture/frost inside the cabinet
• Helps the compressor run less frequently by maintaining a stable internal temperature
• Commonly used when the existing gasket is torn, stretched, flattened, or no longer seals evenly
• Reduces warm spots and food spoilage that can result from a failing door seal

• Clean the door surface and gasket mounting channel before installing to ensure a tight seal
• Align the gasket evenly around the door and press into the channel; warm the gasket with a hair dryer if needed to ease installation (low heat only)
• Check door closing and seal after installation; avoid using sharp tools that can damage the gasket

Color: White

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn seal helps stop warm air leaks, reduce frost and condensation, and keep temperatures stable for better efficiency and food preservation.

• Creates a continuous perimeter seal between the door and cabinet to prevent air infiltration
• Helps maintain correct temperatures and reduce moisture/frost buildup
• Restores proper door closing when the old gasket is torn, warped, or permanently compressed
• Common symptoms: door not sealing or popping open, condensation around the door, temperature swings, frost along the door edges

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Let the new gasket relax at room temperature or warm it in water to remove kinks
• Pull the old gasket from the door channel; clean the mating surface
• Seat corners first, then press the gasket fully into the channel; use gentle low heat to smooth waves if needed

The Door Gasket is an OEM part for Whirlpool refrigerators. It forms an insulating perimeter around the refrigerator door opening to maintain cool interior temperatures during use.

Causes relate to the breakdown of sealing materials from repeated compression cycles over many years. Cracks or loose areas compromise the barrier.

Symptoms of a defective door gasket can include:

• Warm air entering around the door edges
• Interior humidity increases causing frost or condensation
• Higher electric bills from lost cooling efficiency
• Inability to maintain set temperatures over long periods

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Color - Grey

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

The Freezer Door Gasket is an OEM replacement part for Whirlpool bottom-mount refrigerators. This white freezer door gasket is responsible for maintaining a tight air seal around the entrance to the freezing compartment. It helps retain cold air inside and prevents warm drafts or humidity from affecting food freshness and freezer efficiency. 

Symptoms of a bad freezer gasket include: 

• Difficulty keeping consistent temperatures inside the freezer section
• Visible moisture, frost, or condensation around the door perimeter
• Noticeable warm air infiltration reducing cooling performance

Causes of freezer gasket failure involve regular opening and closing of the door. Over time, the flexible material breaks down from continuous use exposing it to changing environmental temperatures. Physical damage from overstuffing shelves or slamming the door can also prematurely damage the gasket.

This OEM replacement is also compatible with some KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components

The Gasket-Door (black) is an OEM component specifically designed for Whirlpool refrigerators. This rubber gasket forms a seal around the perimeter of the refrigerator door opening. It helps maintain interior temperatures and humidity levels.

Symptoms of a bad door gasket include:

• Inability to properly chill compartments and freezing performance issues  
• Excessive frost or moisture inside refrigerator sections
• Higher energy costs from inefficient temperature regulation
• Warm air infiltration indicated by higher than normal interior temps

Causes of degraded gasket performance typically include cracks, tears or compression set deterioration that compromise the sealed barrier over many years of use. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This evaporator cover gasket seals the evaporator cover to the refrigerator cabinet, helping maintain proper airflow and reducing frost buildup behind the back wall. It restores a tight seal for more reliable cooling performance. What it does:

• Seals the evaporator cover to prevent air leaks that can cause frost or ice buildup
• Helps maintain consistent cold-air circulation in the freezer/refrigerator compartment
• Reduces chances of excessive frost, water pooling, or longer run cycles tied to air infiltration
• Supports normal defrost operation by keeping warm, moist air out of the evaporator cavity

• Disconnect power before servicing and allow the appliance to defrost if needed
• Remove the evaporator cover carefully; watch for sharp sheet-metal edges and retain fasteners
• Position gasket evenly around the cover mating surface; avoid stretching or creasing the seal
• If adhesive or clips are used, replace or reapply per OEM guidance to ensure a secure fit