Mcculloch Parts

This genuine muffler is designed to offer a replacement for select lawn and garden equipment engines. The muffler is part of the exhaust system and it is responsible for reducing the noise from the engine as it exhausts out of the unit. Over time, mufflers are known to get clogged, rust, or otherwise wear out and require replacement. If the muffler becomes clogged or damaged, it will need to be replaced in order to operate the equipment safely. This is a genuine OEM replacement muffler that is manufactured to specific standards. It is made by Weed Eater and is compatible with several of their machines, as well as units from Husqvarna and Poulan. The muffler is sold as an individual unit and does not include the hardware required for installation. It is used in select trimmers, pole pruners, edgers, and lawnmowers. To replace the muffler, it will be important to wear gloves and allow the engine to cool completely. Remove the old muffler and replace it with the new unit, securing it into place with the existing hardware. In the event that the hardware also needs to be replaced, it can be purchased separately.

This replacement part is a piston ring and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This part is used in grass trimmers and backpack blowers. This is an important part of the piston assembly and helps the engine operate properly and efficiently. These rings provide a seal around the piston and the walls of the cylinder. A new piston ring might be needed if the current ones are becoming loose and falling off the cylinder. If the seal around the rings is not tight, this can cause issues within the engine and the user might not be able to operate the machine properly. If the compression is reduced because of the rings, the engine will not run.This piston ring is sold individually. This is a genuine OEM replacement part and is sourced directly from the manufacture. This ensures proper fit in many different appliances.

This ignition coil assembly is a genuine Husqvarna part, sold individually. This ignition coil assembly can be used as a replacement part in a leaf blower. The purpose of the ignition coil assembly in a leaf blower is to transfer the electrical voltage of the battery toward the spark plugs so that the spark plugs can ignite and power on the engine of the leaf blower.The ignition coil assembly in a leaf blower might need to be replaced if the ignition coil assembly no longer is able to serve its critical function toward the powering on of the small engine of the leaf blower. This could occur if the ignition coil assembly is sufficiently damaged in the form of puncturing, scraping, denting, ripping, tearing, fraying, or eroding to the point of reduced functionality. If this occurs, the ignition coil assembly should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This ignition coil assembly is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, and Poulan.

This replacement part is a filter and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This part is used in backpack blowers, trimmers, or edgers. This filter is important to the engine as it is placed around the air filter and prevents any debris or dirt from entering the carburetor. When this filter becomes dirty it can compromise the use of the carburetor and therefore cause issues with the engine. Be sure the engine is powered off before replacing a filter. It is recommended that filters be replaced frequently. Be sure to refer to the specific manual for the appliance for help on replacing this part. This filter is an OEM replacement part sourced directly from the manufacture. This part is sold individually.

This is a carburetor that can work with several types of handheld lawn and garden tools. Carburetors are responsible for ensuring that there is a correct mixture of air and fuel for combustion in the engine. If the owner notices that their equipment is having trouble starting or running continuously, there could be an issue with the carburetor.Carburetors are made from quality materials and are made to last. However, parts of the carburetor can start to wear down over time. In some instances, corrosion could occur, or the bulb could crack. If there are any problems with the carburetor, it should be replaced as soon as possible. Otherwise, owners will have trouble getting their machines started.The carburetor will work as a replacement for select models of blower and trimmer from Husqvarna and Poulan. The part is sold individually. This is a genuine OEM replacement part that has been sourced directly from the manufacturer.

This part is a replacement middle pipe. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective middle pipe in leaf blowers.The middle pipe connects the nzle to the leaf blower and allows a stream of air to be ejected from the equipment. This part may become detached, cracked, or otherwise ineffective over time, requiring replacement. When working on or near an engine it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this middle pipe, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality plastic. This middle pipe can be used with different models of leaf blowers that have been manufactured by Husqvarna, Poulan, and other brands. Part sold individually.

This is a fuel cap that is used with several types of small engine lawn and garden equipment. The purpose of the fuel cap is to make sure that all gasoline in the fuel tank stays in place and there are no leaks present. The fuel cap can experience wear and tear over time or become cracked, broken, or damaged if it impacts other items. If fuel can be smelled through the cap, if the cap doesn't tighten, or if it is otherwise visibly damaged, the fuel cap should be replaced.Prior to replacement or even removing the fuel cap, the equipment should be placed in a well-ventilated area. It's also important to disconnect the spark plug wire to create a safe environment. Empty any fuel in the tank into an appropriate container before moving on. Once empty, you can replace the old cap with a new one.This is a genuine OEM replacement component that is directly sourced from the manufacturer. It is sold as a single fuel cap. The part is created to be compatible with string trimmers, hedge trimmers, and leaf blowers manufactured by Poulan, Poulan Pro, and Craftsman.

A combustion engine will create a lot of pressure by igniting fuel and air with a spark. It features pistons beneath the valves and the cylinder block. Between these areas are the piston rings that have many purposes that include keeping gas compression between the piston and the wall of the cylinder, keeping a layer of lubrication on the inside of the engine, allowing adequate heat transfer, and supporting the piston inside the cylinder. This replacement piston ring is designed for use in a long list of edgers, trimmers, and blowers. It is compatible with Husqvarna, Poulan, and Craftsman machines. This is an OEM replacement part that will require a complex set of steps to install properly. It will require the use of torque wrenches, plug wrenches, pliers, screwdrivers, a mallet, and more to do the repair. It ships individually.

This replacement flywheel assembly for use in chainsaws fits onto the crankshaft. It features magnets along the side that provide an electric charge when the magnets go past the ignition module. The electric charge that is created by the flywheel and ignition module passes to the spark plugs, which spark the air-fuel mix in the cylinder. The metal flywheel could become corroded, which can make parts of it brittle. Over time, the flywheel could also become worn down from natural use, and it might no longer function properly. This would mean that it would be difficult or even impossible to start the chainsaw. When this part fails, owners should replace it right away. The authentic OEM chainsaw flywheel assembly is sold individually. It is made to work with chainsaws, and it is compatible with several different brands including Husqvarna, Craftsman, Poulan, and Poulan Pro.

This is a high-quality assembly seal and bearing that is used on chainsaws by several manufacturers. The purpose of the ball bearing is to reduce friction between various moving parts in a chainsaw or another tool. The component is also used to stabilize and hold the position and angle of specific parts in lawn and garden equipment. The assembly seal and bearing experience substantial wear and may need to be replaced regularly. When replacing the assembly seal and bearing in a chainsaw, basic tools will be needed. A screwdriver, a pair of pliers, a socket set, and an impact wrench may be required for the process. First, take the chainsaw and place it on a stable and level surface. Make sure it is powered off before disconnecting the spark plug wire. The engine will need to be removed to replace the bearing and its seal. Test the tool before further use.This assembly seal and bearing are designed for use with Husqvarna, Craftsman, and Poulan chainsaws. The part is sold on an individual basis with one seal and one bearing. It is a genuine OEM replacement component that is directly sourced from the manufacturer.

This bar adjuster knob is used on a variety of chainsaws. It works by adjusting the amount of bar tension which helps to tighten the chain on a chainsaw. Without the part, the tension of the bar would not be kept in the correct area and the chain could come loose. This could result in a chainsaw that doesn't run or is too dangerous to use. A visual inspection of the knob can indicate if it is damaged or no longer working correctly.If the bar adjuster knob needs to be replaced because it's stripped or otherwise damaged, the process is simple. A hammer and screwdriver will be required to make the replacement. Pull on the handle of the adjustment knob and place a screwdriver inside to remove it. A flat screwdriver can be placed against the metal nut at an angle. Hit the back of the screwdriver with a hammer to pull the nut loose if the knob is stripped. This will help remove the knob and install a new one.This bar adjuster knob is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold individually. It is compatible with many Poulan Pro, Craftsman, and Husqvarna chainsaws.

The ignition module is an assembly that includes the condenser and the ignition boot coil that connects to the spark plug. It creates the power to generate the spark as the flywheel magnet passes the module. Then it transfers that energy into the spark plug, which will power the engine and keep it running. If the engine is idling rough or starts and then dies, it could be a sign that the spark plug or ignition module are bad. In severe cases, the engine might not start at all. Since spark plugs are a part of routine maintenance, it's usually the later issue. This ignition module can provide an exact fit for select machines. This genuine OEM ignition module is manufactured by Husqvarna to exact standards. It can be used with a number of chainsaws from Poulan, Craftsman, and Mcculloch. This durable unit is made of plastic, rubber, and metal and is sold as an entire assembly. No hardware or other accessories are included with the purchase. Always wear gloves and allow the engine to cool before performing any parts repairs or replacements.

This part is a replacement screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a stripped or misplaced screw in a variety of outdoor power equipment. This screw is a genuine piece of standard hardware that can have many potential uses. It's important to use screws sourced from the manufacturer to ensure a proper fit and high quality. Screws are essential for securing parts and holding the equipment together and should be replaced if worn, broken, or lost. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this screw is suitable for use on several different models of blowers, edgers, and trimmers manufactured by MTD, Ryobi, Yard Man, Cub Cadet, and Troy-Bilt. This is a genuine part made of high-quality, durable metal and is sold individually.