Norge Parts

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.

This is a set of eight replacement control knobs designed to restore function and appearance to compatible Whirlpool appliances. The kit gives you matching knobs to operate controls and replace cracked, faded, or missing pieces. What it does:

• Replaces worn, cracked, or missing control knobs so you can reliably set cycles, temperatures, or power levels
• Restores a uniform look across the appliance control panel
• Provides a direct-fit replacement for appliances that use the 8-knob kit
• Helps improve grip and control when turning settings

• Remove old knobs by pulling straight off the splined shaft; align new knob spline and push onto the shaft until fully seated
• No special tools typically required; use gentle force to avoid damaging the shaft
• If knobs control electrical functions, ensure appliance controls are off before replacing; disconnect power or gas if advised by the appliance manual

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket

This motor overload protector helps prevent the dryer motor from overheating by cutting power when excessive current or heat is detected. It restores normal operation when the motor cools or the overload is replaced. What it does:

• Protects the dryer motor from damage by interrupting power during overheating or overcurrent conditions
• Commonly used when the dryer motor won't start, hums but doesn't run, or the motor trips repeatedly
• Works with the motor start system to reduce the risk of burned windings and costly motor failure
• Resets or is replaced to restore normal motor operation after an overload event

• Always unplug the appliance before checking or replacing this part
• Inspect wiring and motor for underlying issues that can cause repeated overloads

This genuine pin hinge secures and guides the appliance door, restoring smooth pivoting and proper alignment for reliable opening and closing. It's a direct-fit replacement designed to help stop door sag, binding, or uneven gaps. What it does:

• Provides the pivot point that lets the door swing open and closed
• Keeps the door aligned to the cabinet for a proper seal and even gap
• Replaces worn or bent pins that cause door sag, scraping, or noisy operation
• Helps restore smooth, wobble-free door motion

• Disconnect power (and water for dishwashers) before starting work
• Support the door during removal to prevent dropping or damage
• Simple hand tools typically required; reuse original screws unless damaged
• If the door has glass or heavy panels, get a helper to hold weight during installation

This is a replacement screw used to secure appliance panels and components so parts stay firmly mounted and functioning. Use it to replace a missing or damaged fastener for a secure repair. What it does:

• Fastens panels, brackets, or small components to prevent loosening or vibration
• Helps stop rattling, shifting, or gaps caused by a missing or stripped screw
• Restores proper alignment of mounted parts after repair or maintenance

• Use the matching driver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent damage to threads or surrounding parts
• Disconnect power and follow manufacturer safety guidelines before servicing the appliance
• Replace like-for-like: screw size and head type match the original before installation

This brown lock lever is a direct-replacement actuator that engages the appliance's locking mechanism so doors or lids stay securely closed during cycles. Restores proper latch movement and helps the door lock and release as intended. What it does:

• Moves the door/lid latch into the locked or released position when the appliance runs
• Replaces a worn, broken, or bent lever that prevents the lock from engaging
• Helps eliminate symptoms such as a door that won't latch, won't stay closed, or won't unlock at cycle end
• Works as the mechanical interface between the lock assembly and the door/lid

• One brown lock lever (single replacement part)

• Disconnect power and water (if applicable) before servicing to avoid shock or injury
• Access may require removing the control panel or door trim depending on model; follow OEM instructions
• Inspect mating latch and fasteners; replace any damaged clips or screws for secure fit

Color: Black