Norge Parts

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation

This replacement light bulb restores clear, reliable illumination so you can see contents and monitor appliance operation. Replace a burned-out, dim, or flickering bulb to bring visibility back to the area it lights. What it does:

• Provides illumination in the appliance's interior or designated lighting location
• Makes it easier to see contents and check status at a glance
• Common symptoms: light won't turn on, intermittent/flickering light, dim or blackened bulb

• 1 light bulb

• Disconnect power before servicing; allow hot surfaces and the old bulb to cool completely
• Remove any lens/cover, then remove the old bulb
• Install the new bulb securely without overtightening; reinstall the lens/cover if present
• Restore power and test operation

This overload protector is a safety device that mounts on the compressor and opens the circuit if overheating or excessive current is detected. Replacing a failed protector can help restore reliable compressor start-up and protect the motor from damage.

• Monitors compressor temperature/current and interrupts power during an overload condition
• Helps prevent compressor overheating and winding damage
• Common symptoms: refrigerator not cooling, compressor won't start, clicking or humming then shutting off, repeated cycling from the rear machine compartment
• Visible heat damage or a burnt odor at the start device area may indicate failure

• Disconnect power before servicing; work in a well-ventilated area
• Access the rear machine compartment; remove the cover to reach the compressor start assembly
• Note wire positions and orientation; the overload fits on the compressor terminal alongside the start device/relay—seat it fully and securely
• Inspect connectors for heat damage and ensure tight, clean terminals before restoring power

This white freezer door handle restores a secure, comfortable grip and refreshes the appliance's appearance. Replace a cracked, loose, or missing handle so the freezer door opens and closes smoothly again. What it does:

• Replaces a damaged, worn, or missing freezer door handle
• Restores proper grip and leverage for normal door operation
• Helps address loose or wobbly handle conditions
• Matches the original white finish for a clean, uniform look

• Wear gloves and protect the door surface to avoid scratches
• Support the handle while loosening/removing existing fasteners
• Reuse existing hardware as designed; start screws by hand and tighten just until snug
• Check alignment and security before returning the appliance to service

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

By Maytag/Magic Chef. Set of 4 chrome square drip pans for gas ranges / cooktops. Fits many brands, including Maytag, Magic Chef, Admiral, Crosley, Norge, Jenn Air and others. Matching set of grates: 1430291.

This idler spring maintains proper tension on the dryer drum belt by keeping the idler pulley engaged. Replacing a weak or broken spring restores consistent drum rotation and helps prevent belt slippage and squealing during operation.

• Maintains belt tension by pulling the idler arm/pulley against the drum belt
• Helps the motor start and keep the drum turning smoothly
• Reduces belt slippage that can cause squealing or chirping
• Common symptoms of a failed spring: drum won't turn or turns intermittently; belt comes off or feels loose; loud squeal from idler area

• Disconnect power; for gas dryers, shut off the gas supply
• Access the idler assembly; relieve belt tension and note belt/spring routing before removal
• Attach the new spring to the same holes/orientation on the idler arm and base; verify belt path
• Rotate the drum by hand to confirm alignment and tension before reassembly

This lid switch assembly kit is the washer's safety interlock. It detects when the lid is closed so the control can allow the machine to spin, helping restore safe, reliable operation when the original switch fails.

• Senses lid closed and enables the spin cycle
• Prevents spinning with the lid open for safety
• Common failure symptoms: no spin or intermittent spin
• Requires pressing or jiggling the lid to run; no audible "click" when closing the lid

• Disconnect power before servicing
• Access the switch under the top/console area; remove the old switch/bracket as designed
• Route wiring along the original path and secure away from moving parts
• Align the actuator so the lid reliably engages the switch; test spin operation before reassembly

This surface burner knob fits the valve stem for a cooktop/range burner control. It restores a secure grip and accurate adjustment when the original knob is cracked, stripped, loose, or missing.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame level
• Replaces a knob that slips, won't stay on, cracks, melts, or free-spins
• Helps restore proper Off alignment and a clean, finished look

• Ensure all controls are in the Off position; disconnect power and shut off gas as a safety precaution
• Pull the old knob straight off the valve stem—do not pry sideways
• Align the flat/D-shaped opening with the valve stem and press firmly until fully seated
• Verify smooth operation and correct Off alignment before restoring power/gas

Left hand side.

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

This is a replacement control knob for the freezer temperature control shaft. It restores a secure grip and clear detent positions so you can set the freezer temperature easily. What it does:

• Replaces a cracked, worn or missing freezer temperature control knob
• Provides a firm grip and visible setting position for accurate adjustment
• Allows the control shaft to turn and stay at selected settings
• Helps resolve symptoms like a loose, spinning or non-engaging knob

• Disconnect power to the appliance before attempting replacement
• Pull the old knob straight off the control shaft; align and push the new knob fully onto the shaft until it seats
• If resistance is felt, stop and inspect the shaft and knob for debris or damage before forcing
• If the control shaft is damaged or the knob does not secure properly, replace the control.

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.

This is a set of eight replacement control knobs designed to restore function and appearance to compatible Whirlpool appliances. The kit gives you matching knobs to operate controls and replace cracked, faded, or missing pieces. What it does:

• Replaces worn, cracked, or missing control knobs so you can reliably set cycles, temperatures, or power levels
• Restores a uniform look across the appliance control panel
• Provides a direct-fit replacement for appliances that use the 8-knob kit
• Helps improve grip and control when turning settings

• Remove old knobs by pulling straight off the splined shaft; align new knob spline and push onto the shaft until fully seated
• No special tools typically required; use gentle force to avoid damaging the shaft
• If knobs control electrical functions, ensure appliance controls are off before replacing; disconnect power or gas if advised by the appliance manual

This motor overload protector helps prevent the dryer motor from overheating by cutting power when excessive current or heat is detected. It restores normal operation when the motor cools or the overload is replaced. What it does:

• Protects the dryer motor from damage by interrupting power during overheating or overcurrent conditions
• Commonly used when the dryer motor won't start, hums but doesn't run, or the motor trips repeatedly
• Works with the motor start system to reduce the risk of burned windings and costly motor failure
• Resets or is replaced to restore normal motor operation after an overload event

• Always unplug the appliance before checking or replacing this part
• Inspect wiring and motor for underlying issues that can cause repeated overloads