Kenmore Refrigerator 795.71072012 (79571072012, 795 71072012) Parts

In 2012 I purchased an LG French door bottom freezer fridge. this thing was a problem from day one, I had to call 3 technicians where I bought it from- a nameless major retailer. through the 2 1/2 years I have had it, the problems were always with the ice cube maker, and finally, the motor finally stalled. I was able to revive it, but only for a short time- then I went to replace the unit all together and searched high and low until I came across Appliance Pros. I actually had no idea that 2 of... Read more

• Leaking
• Not dispensing water

I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more

• Leaking

Removed the old line and replaced with the new. This is the sixth time I've replaced the line. Yes you read that right, the sixth time. Lines fail about every 6-8 months so I can change one out now in about 10-15 minutes. Bought the refrigerator in Feb '09 and the line first failed in March 2012. Since then I've had failures in as little as 4 months to as much as 9 months. Frustrating to say the least, but I'm a whiz at changing out the line :-) Read more

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

• Fridge too cold
• Fridge too warm

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

Ordered new tube part AJR56656503 for Lg LFX25978ST/01 watched a lot of videos but none showed how to remove the door tube end from its connection so I just cut and spliced the new tube to the old under the cover for the door hinge area after feeding it from the back of frig to that area. It was easy till I tried to remove the line end from ice maker area. Read more

Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more

Replaced icemaker Read more

All parts I ordered fit perfectly Read more

It was just a broken bin. We replaced it. Read more

The ice chute flap wasnt closing. 1. I turned off power 2, Pulled off facia around controls on freezer door,, you have to pull out the bottom part of the chute first , its clipped in 3. Disconnected the front panel 4. Unscrewed the next panel to allow access to the chute flap 5. Removed 1 screw holding complete flap and mechanism and replaced with new 6. Re installed all parts in reverse Problem was the chute flap had worn and was folding over on top edge when opened and then wouldnt return... Read more

We have an LG fridge that is 10 years old that was starting to have sweating problems around all the gaskets. So it was either a new fridge or try replacing the gaskets. I purchased a new ice maker door gasket using the parts catalog on the website. Very easy to order and they offer a short video to show the technique to switch out the old and new gaskets. Also did the same thing with the door gaskets and freezer drawer gasket. Website was very easy to work with and find the correct parts and... Read more

Ordered parts, removed top tray in freezer, popped the back inside freezer panel out removed and replaced fan, dampers and fan housing. Took about 15 minutes. Read more

Appliance Parts was the only one of three companies that did it right. When the glass in our rather new LG fridge broke, I called the number listed in the manual for replacement parts and was put through to their "authorized distributor" for our area. The authorized distributor sent us the wrong part (entirely different dimensions) with a packing slip identifying the right part number. Because this is not a review of that company (which would be horrible, I won't share the gruesome details of... Read more

Threaded bases for two roller screws were ~ 80% broken off. Used a short (just barely extends past the end of the roller) sheet metal screw to secure the roller in the upper sliding section of the handle (handle in place first). The head was thick enough to fill the gap between the roller and the cover. Filling that gap accurately is important. Need to keep the roller pushed into the recessed area in the door. (Do a test fit with the parts before trying to install them on the door). Turn the... Read more

Unplugged frig to check connections, everything was ok. When I plugged it back in, nothing worked and the display and ice maker were flickering and clicking. Unplugged the display connector on the main board and could hear clicking from the main board itself. Replacing the main board and capacitor fixed it. I only replaced the capacitor as a precaution. it may not have been bad, but I did it for good measure. Everything is working great now and I don't have to buy a new refrigerator. Read more