Bosch Dishwasher SHU9902 UC/06 Parts

This dishwasher door gasket seals the sides and top of the tub opening to keep water and steam contained during a cycle. Replacing a worn seal helps stop leaks at the door edges and restores quiet, efficient operation.

• Forms a watertight seal between the door and the tub perimeter
• Helps prevent dripping or puddles at the front corners and along the sides
• Maintains proper wash pressure, temperature, and noise isolation
• Replace if torn, flattened, brittle, or if moisture escapes around the door

• Disconnect power; if uninstalling the dishwasher, also shut off the water supply
• Open the door and pull the old gasket straight out of the channel
• Clean the groove; warming the new gasket in hot water can help relax bends
• Start at the top center and press the gasket fully into the channel without stretching; close the door to seat the seal and run a test cycle to check for leaks

The Roller and Cable Assembly is an OEM part for Bosch dishwashers. This assembly includes the roller and cable, which work together to facilitate the smooth operation of the dishwasher door, allowing it to open and close effortlessly.

Over time, the roller and cable can wear out or become damaged due to regular use, friction, or accidental mishandling. If either component fails, it can affect the balance and movement of the dishwasher door, making it difficult to operate.

Symptoms of a bad roller and cable assembly include:

• Difficulty in opening or closing the dishwasher door
• A sagging or misaligned door
• Unusual noises when operating the door
• The door not staying securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Dishrack Stop Kit is an OEM replacement part for Bosch dishwashers. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack slides on. These stops help keep the rack on the rail, without this part the upper rack of your dishwasher will not slide in and out of your dishwasher properly.

Causes of faulty dishrack stops include wear of sliding surfaces through repetitive racking and unracking over extended use. Exposure to moisture in the wash chamber environment can accelerate degradation.

Symptoms of a bad dishrack stop kit include:

• Dishracks slipping during rotation potentially damage fine china
• Clearance issues where racks impact other interior components
• Potential tipping if stops fail to release rack load onto door interior

This OEM Bosch part is also compatible with Thermador, Gaggenau and some Kenmore models.

The Screw (Toe Kick) is an OEM part for Bosch dishwashers. It is a mounting fastener that secures the toe kick panel to the bottom frame of the appliance. As a low-profile screw, it serves an important aesthetic purpose while maintaining structural integrity.  

Causes of a failed screw can include wear and deterioration from constant vibrations during cycles, or physical damage if the toe kick panel is impacted. 

Symptoms of loose or missing toe kick screws include:

• Sagging or detachment of the toe kick panel from the dishwasher
• Unsightly gaps appearing below the appliance  
• Possible shifting of the entire dishwasher if not properly secured
• Access issues for cleaning beneath the unit

Replacing with this genuine Bosch screw restores proper mounting of the external panels. It is also compatible with some Asko, Thermador, and Jenn-Air specialty dishwashers. 
 

This assembly includes the handle. Color: gray. Measures about 5 inches wide by 9 inches high by 9 inches deep.

The Silverware Basket Assembly is an OEM part for Bosch dishwashers. This basket is located in the lower rack and is used to hold utensils securely during the wash cycle.

Causes of a bad silverware basket can include damage from normal wear and tear over time or bending/warping from overload.

Symptoms of a dysfunctional basket include:

• Silverware clustering and not receiving thorough cleaning
• Tines bending or breaking off from the basket
• Dividers popping out of place
• The basket shaking or slipping during the wash cycle

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Dispenser Gasket is an OEM part for Bosch dishwashers. This gasket forms a seal around the detergent dispenser, ensuring that water and detergent are properly contained within the dispenser until they are released during the wash cycle. It helps prevent leaks and ensures efficient operation of the dishwasher’s detergent system.

Causes of a bad dispenser gasket can include regular wear and tear, exposure to high temperatures, and the use of harsh detergents. 

Symptoms of a bad dispenser gasket include:

• Leaks around the detergent dispenser area
• Detergent not being dispensed properly
• Visible cracks or wear on the gasket
• Water pooling inside or outside the dispenser

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This Sump Gasket is an OEM part for Bosch Dishwashers. It seals the dishwasher sump to prevent water leaks during the washing cycle. Continuous exposure to water, detergent, and heat can lead to wear or damage to this component.

What Causes a Bad Sump Gasket: 
Exposure to hot water, chemicals in detergents, and constant water pressure can cause the sump gasket to deteriorate or develop tears.

Symptoms of a Bad Sump Gasket:

• Water leakage from the dishwasher
• Incomplete washing cycles
• Visible tears or damage to the gasket

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Note: Due to a factory design change, connector part# 00623143 may also be needed.
 

The Lower Spray Arm is an OEM part for Bosch dishwashers. This part is responsible for spraying water and detergent solution onto the dishes during the wash cycle, ensuring thorough cleaning.

Causes of a malfunctioning Lower Spray Arm can include clogging or obstruction from food debris, mineral buildup, or foreign objects.  

Symptoms of a bad Lower Spray Arm include:

• Poor cleaning performance, with dishes coming out dirty or with food particles remaining
• Water not spraying evenly or failing to rotate during the wash cycle
• Loud grinding or knocking noises coming from the spray arm area

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

NTC (negative temperature coefficient). Resistance or capacitance decreases when temperature increases.

The Temperature Sensor with Hi Limit Thermistor is an OEM part for Bosch dishwashers. This sensor monitors internal temperatures, providing feedback to the control module during each cycle.

Causes of failure can be related to mineral buildup over time interfering with sensing or physical damage to wiring or connectors.

Symptoms of a bad temperature sensor include:

• Abnormal or inconsistent wash temperatures
• Error codes related to temperature issues
• Reduced cleaning performance from improper heating

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

2 clamps included.

The Detergent Dispenser Assembly is an OEM part for Bosch dishwashers.  The detergent dispenser assembly works with the control system to release detergent during the wash cycle.  

Causes of a bad detergent dispenser assembly can include broken or loose mounting points, a dispenser that no longer locks into place, or a damaged latch mechanism preventing the dispenser from opening.

Symptoms of a bad detergent dispenser assembly include:

• Detergent not dispensing or distributing as intended
• Dispenser door unable to close or remains open
• Excess clutter inside the dishwasher
• Ineffective cleaning or dirty dishes after cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Drain Pump Cover is an OEM part for Bosch dishwashers. This cover protects the drain pump mechanism from debris while draining dirty water after each cycle.

Causes of a bad drain pump cover include cracks or breaks from heavy impacts over time.

Symptoms of an improperly functioning cover include:

• Leaks in the area around the drain pump
• Decreased drain and pump performance over time
• Potential clogs from broken pieces inside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Upper Spray Arm Water Tube is an OEM part for Bosch dishwashers. It is a vital component of the washing mechanism responsible for spraying water across the upper rack. 

Over time, mineral deposits can clog the narrow openings of the water tube, reducing water pressure and spray effectiveness. Accidental bending or cracking of the flexible water tube could also cause spray issues.

Symptoms of a bad upper spray arm and water tube include: 

• Incomplete cleaning of dishes on the upper rack
• Dried food soils left behind after washing  
• Noticeably weaker water spray pressure from the arm
• Possible leaks or drips around the arm connection point

Replacing with this OEM Bosch part restores full spray coverage and optimized washing for all rack levels. It is also compatible with certain Miele, Asko, and Jenn-Air professional-grade dishwashers.
 

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

The Pressure Chamber is an OEM part for Bosch dishwashers. This part is responsible for monitoring and controlling the water level within the dishwasher. It operates by sensing the pressure exerted by the height of the water in the tub and ensures that the dishwasher fills with the correct amount of water for optimal cleaning performance.

Causes for replacement may involve wear and tear over extended use, mineral buildup affecting the switch’s sensitivity, or electrical faults leading to inconsistent performance.  

Symptoms of a failing Pressure Chamber include:

• Overfilling or underfilling of the dishwasher, which can lead to inadequate cleaning or potential water damage.
• Unexpected changes in the wash cycle, such as sudden stops or pauses.
• The dishwasher not starting a wash cycle due to incorrect water level readings.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.