Kenmore Refrigerator 106.50272010 (10650272010, 106 50272010) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196195
The Dispenser Door Pin Kit is an OEM part for Whirlpool refrigerators. This kit includes the pins that secure the dispenser door, allowing it to open and close smoothly when dispensing ice or water.
Causes of a bad dispenser door pin kit can include normal wear and tear, breakage from frequent use, or damage due to mishandling.
Symptoms of a bad dispenser door pin kit include:
- The dispenser door not opening or closing properly
- Leaks or drips from the dispenser area
- Loose or misaligned dispenser door
- Difficulty in dispensing ice or water
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken tab on ice door Jeffery J. • Mustang , OK • December 19, 2015
It was not looking good. I could not order the part I needed as it was part of the door - eve though it had screws att Hong it to the freezer door. At one web site it was a replacement of the whole freezer door!/? Luckily I ventured further and found this repair kit and video instructions. My order arrived in 3 days, and the install (thanks to the video) was easy. A whole lot better than buying a new freezer door - not!
BTW - Whitlpool should not have made the tabs out of plastic, the metal...
Read more
More
$8.57
- Compare At:
-
$10.20
- You Save:
-
$1.63
Genuine Whirlpool part
By: Whirlpool
Part Number: W11223328
This shelf support stud anchors a refrigerator shelf to the cabinet liner so it stays level and secure. Replace a cracked or missing stud to restore proper support and prevent shelves from tilting, slipping, or dropping.
- Locks into the liner wall to provide a mounting point for the shelf frame or bracket
- Keeps the shelf aligned and at the correct height
- Common symptoms: broken/missing stud, shelf won't sit flat, shelf sags or falls on one side
- Helps prevent items from sliding due to an unstable shelf
What's included: One shelf support stud Install notes:
- Disconnect power; remove the shelf and any items resting on it. Handle glass shelves carefully and consider wearing cut-resistant gloves.
- Remove the damaged stud (release the locking tab or twist out, depending on design).
- Insert the new stud into the existing hole until fully seated and locked.
- Reinstall the shelf and verify it sits level before reloading.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$15.95
- Compare At:
-
$18.98
- You Save:
-
$3.03
Genuine Whirlpool part
By: Whirlpool
Part Number: 2159080
Color: Black
Do-It-Yourself Stories from Customers like You
Worn out freezer gasket Jeffrey T. • Norfolk , VA • February 18, 2020
Bought gasket from website, followed easy helpful video instructions, perfect fit.
Read more
More
$148.50
- Compare At:
-
$178.20
- You Save:
-
$29.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152858
Color: White
Do-It-Yourself Stories from Customers like You
The ice dispenser lever was cracked and did no longer trigger the dispensing of the ice Andrea M. • Honolulu , HI • March 01, 2015
I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better.
I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some...
Read more
More
$53.33
- Compare At:
-
$64.00
- You Save:
-
$10.67
Genuine Whirlpool part
By: Whirlpool
Part Number: W11594405
The Axle is an OEM part for Whirlpool refrigerators. This axle allows it to be easily repositioned or moved for cleaning and maintenance. It supports the rollers that enable the refrigerator to glide across the floor.
Common causes of a bad axle include prolonged use, excessive weight, or impact damage, which can lead to the axle bending or breaking.
Symptoms of a bad refrigerator roller axle include:
- Difficulty moving the refrigerator
- Uneven or wobbling movement
- Scratches or damage to the floor
- The refrigerator not staying level
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Maytag refrigerator one front plastic roller (wheel) broke Kenneth S. • Manhattan , IL • April 05, 2019
Watched the video on how to replace. Ordered new roller, which was delivered in just a couple of days. Since the roller had broke, I was unable to roll out the refrigerator, so I tilted the refrigerator back and placed a small furniture slider under the roller frame to prevent gouging the wood floor. Then it was easy to slide out the refrigerator and replaced the roller as explained on the video. I had ordered a pin and bolt, just in case I would need to replace, but didn't need them. ...
Read more
More
$16.95
- Compare At:
-
$20.17
- You Save:
-
$3.22
Genuine Whirlpool part
By: Whirlpool
Part Number: W11496481
The Water Tube is an OEM component specifically designed for Whirlpool refrigerators. This 1/4" diameter water tube provides a pathway for water to flow through the refrigerator's internal components during operations like ice production.
Causes of a bad water tube can include cracks or defects from manufacturing, damage from impact or abrasion during shipping or installation, or wear over time from cycles of use.
Symptoms of a bad water tube include:
- Water leaks or drips inside the refrigerator
- Insufficient or slow water flow to components
- Abnormal sounds from water not flowing smoothly
- Failure of components dependent on water flow like the ice maker
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore refrigerator models.
Do-It-Yourself Stories from Customers like You
Water filter housing leaking H M. • Picayune , MS • August 18, 2015
Replaced filter housing, and both water tubes
Read more
More
$26.95
- Compare At:
-
$31.80
- You Save:
-
$4.85
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2198661
This top coupling links two drive components in select washers to transfer rotation smoothly. Replacing a worn or stripped coupling restores consistent agitation/spin and can reduce slipping, rattling, or grinding noises from the drive area. What it does:
- Connects mating shafts/components so power is transmitted through the drive system
- Helps maintain alignment and cushions minor shock to protect other parts
- Failure symptoms may include no or weak agitation/spin, intermittent drive, or clicking/grinding sounds
- Visual clues can include cracks, rounded/stripped splines, or excessive play
What's included:
Install notes:
- Disconnect power; turn off water supply if moving the appliance
- Access location varies by model; cabinet/top or front panel removal may be required
- Note orientation of flats/splines and seat the coupling fully—do not hammer into place
- Inspect the mating hub/shaft; replace worn companion parts to prevent rapid re-wear
Do-It-Yourself Stories from Customers like You
Broken drive on door dispenser for ice maker Richard H. • Bartlett , TN • March 07, 2016
My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday...
Read more
More
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Whirlpool part
By: Whirlpool
Part Number: W11512417
The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan.
Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.
Symptoms of a bad drain connector include:
- Water or condensation leaks around the connector area
- Puddles or watermarks on the floor behind the fridge
- Slow drainage of water from the evaporator fan coil
- Mold or mildew growth near the connector or drain area
This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The problem was ice buildup on the floor of the freezer William B. • Pahoa , HI • January 15, 2016
A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction....
Read more
More
$25.95
- Compare At:
-
$31.14
- You Save:
-
$5.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10224328
For the complete ice door kit order W10823377.
Do-It-Yourself Stories from Customers like You
Ice dispenser chute door was not closing or sealing Robert H. • West Palm Bch , FL • July 23, 2025
The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable...
Read more
More
$48.95
- Compare At:
-
$57.76
- You Save:
-
$8.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206671B
Color: black. Measures about 9 inches wide by 2-1/2 inches deep.
Do-It-Yourself Stories from Customers like You
Stopped dispensing water Cristopher C. • Santa Rosa , CA • July 15, 2016
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey.
Read more
More
$55.38
- Compare At:
-
$65.35
- You Save:
-
$9.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2198608
The Whirlpool latch spring is an OEM replacement part responsible for securing the ice container or bin in place on a refrigerator. Its main function is to provide tension and support to the ice container latch, allowing it to engage and disengage properly. When the ice container is inserted into the refrigerator's ice compartment, the latch spring ensures that it securely locks in place, preventing accidental spillage of ice.
Causes of a bad latch spring can include metal fatigue from repeated use, rust or corrosion from exposure to moisture, or physical damage from accidental impacts.
Symptoms of a bad latch spring include:
- The ice container not staying in place and sliding out of position
- Difficulty in properly attaching or detaching the ice container from the refrigerator
- The ice container feeling loose or wobbly when inside the ice compartment
- The ice container not aligning correctly with the ice dispenser or auger
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Ice will not dispense from door John J. • Scottsdale , AZ • December 29, 2019
I replaced the driveshaft and the latch on the ice bin as well as the washer that prevents moisture and water from getting down the driveshaft and into the motor. It was an easy job, especially with the video.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152859
Color: Black
Do-It-Yourself Stories from Customers like You
Refrigerator water dispenser stopped working Carlos R. • Houston , TX • September 19, 2014
The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place...
Read more
More
$51.28
- Compare At:
-
$61.02
- You Save:
-
$9.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Circuit breaker would reset once refrigerator goes into defrost mode John C. • Elk Grove , CA • November 16, 2016
Replaced defrost heater with the help of the appliance parts pro how to video.
Video had made doing the job with ease. Had a laptop next to me making sure I had not missed a step. Been a week and things been all good. Well worth it. Thank you!
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Bracket Bryan S. • Garnett , KS • June 28, 2019
Myself
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196483
The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.
Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.
Symptoms of a bad shelf stud include:
- Shelves not staying securely in place
- Shelves tilting or collapsing
- Visible cracks or damage to the stud
- Difficulty in inserting or removing shelves
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08