Kenmore Refrigerator 106.58729800 (10658729800, 106 58729800) Parts

Checked air damper, it was blocked with ice. Replace it and defrosted it. Good to go. Read more

Ordered the parts, took door off the refrigerator. Removed all parts and replace with new parts. Took me about 15 minutes to complete. Read more

It was not looking good. I could not order the part I needed as it was part of the door - eve though it had screws att Hong it to the freezer door. At one web site it was a replacement of the whole freezer door!/? Luckily I ventured further and found this repair kit and video instructions. My order arrived in 3 days, and the install (thanks to the video) was easy. A whole lot better than buying a new freezer door - not! BTW - Whitlpool should not have made the tabs out of plastic, the metal... Read more

Myself Read more

Undid a handful of screws, put the new panel in place and screwed them back in. Read more

I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more

Replaced filter housing, and both water tubes Read more

My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday... Read more

I replaced the pads on my Kitchenaid side-by-side. I was able to order ones that looked exactly like the old ones. It was even easier than what I had seen in a YouTube video. Read more

A YouTube video: https://www.youtube.com/watch?v=jIdtNdDXFDk , by a professional appliance repair company described replacement of the freezer drain pipe with Kenmore's (by Whirlpool) revised drain pipe. Ice buildup inside the freezer was caused by warm air beneath the freezer contacting cold air from inside the freezer the resulting condensation freezing and blocking the drain, causing the ice buildup inside. The revised drain tube functions as a p-trap to prevent cold/warm air interaction.... Read more

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot Read more

Took the broken bin out and put the new bin in. all of maybe two minutes. Read more

Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more