Kenmore Refrigerator 106.59512992 (10659512992, 106 59512992) Parts

Found the parts in the diagram of my fridge and simply installed it very easy Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

• Ice maker won't dispense ice

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

Checked air damper, it was blocked with ice. Replace it and defrosted it. Good to go. Read more

Ordered the parts, took door off the refrigerator. Removed all parts and replace with new parts. Took me about 15 minutes to complete. Read more

It was not looking good. I could not order the part I needed as it was part of the door - eve though it had screws att Hong it to the freezer door. At one web site it was a replacement of the whole freezer door!/? Luckily I ventured further and found this repair kit and video instructions. My order arrived in 3 days, and the install (thanks to the video) was easy. A whole lot better than buying a new freezer door - not! BTW - Whitlpool should not have made the tabs out of plastic, the metal... Read more

Myself Read more

My 16 year old son ordered the part and replaced the part. It took him less than 5 minutes to replace the part. Read more

I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more

• Won't start

Took the screws off the back plate at the bottom and watched the YouTube video on how to remove the cover plate for the starter and overload on the back of the compressor. Ended up snapping the old cover plate (brittle plastic) so I was glad the "kit" came with a new one. I used a small flat-head screwdriver and carefully pried off the starter and overload, then, with the new ones in hand, took the wires off the old ones and immediately put them on the new ones so I didn't lose track (there is... Read more

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The... Read more

I ordered one from you. Read more