Kenmore Refrigerator 106.9542812 (1069542812, 106 9542812) Parts

• Ice maker dispenses too little ice
• Ice maker won't dispense ice

Plastic drum was broken and wasn't pushing the ice through the crusher teeth. Received my part pronto and made the repair. Was an easy fix, took about 15 min from start to finish. Everything working very good now. ( : Thanks for getting the parts to me so fast. I will definitely remember Appliance Pro if I need parts in the future. Read more

Touch up paint Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

I ordered a new handle from Applisnce Parts Pros. It fit the refrigerator perfectly. I reused some of the old screws and ordered one new screw with a cover to attach the bottom of the handle. Now the refrigerator looks as good as new! Read more

• Not dispensing water

After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

My Whirlpool fridge is 12 yrs old. The crisper drawer supports finally gave up. I googled the make and model number for repair parts and AppliancePartsPros.com came up. I was actually surprised that I found the support peg and stud. I watched the video on their site on how to replace them, saw that it was easy and ordered the parts that afternoon. To my utter amazement the parts came via FedEx the following afternoon! I have to admit if I didn't watch the video I wouldn't have known how... Read more

The broken track and shelf stud were the most important part of the repair. I was astounded to find parts for a 20 year old fridge. I was concerned about how to remove the damaged stud. As luck would have it, your site contained a video on how to remove it. Without the video, I would not have been so successful and would most likely have done more harm than good. All I needed for the repair was an open end wrench. It took about 30 seconds to remove and replace. I could not be more please... Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

Well, I took it out (it slides out) to get a good look at it,so i could ref pictures on your site..naturally I had serial/model of refrig,and thats mandatory to get the right part. It came in 2 days,,and being just the bucket, it took only a few minutes to transfer the auger assembly/cube/crusher.... into the new one, 6 screws total..Your site has excellent vids on DIY.......I HIGHLY reccomend. Whole process was'nt over 15 minutes, piece of cake....And NOW i can go back to my nightly 'scotch... Read more

Replacing the cold control solved the problem. While i was at it i also replaced the defrost timer and installed a new ice door. Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more