Kenmore Refrigerator 106.9552882 (1069552882, 106 9552882) Parts

Found the parts in the diagram of my fridge and simply installed it very easy Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

• Ice maker won't dispense ice

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

Although the solenoid I purchased did not fix the problem, nor the "mother electronic board", or the motor, my experience with Appliance Parts Pros has been excellent. Extremely easy to look-up parts for my model refrigerator. Best part is their video instruction that gives you step-by-step hands-on how to remove and install. I would highly recommend these folks. If a lady such as myself can do repairs based on their instruction, anyone can. Thank you for providing such an informative... Read more

Checked air damper, it was blocked with ice. Replace it and defrosted it. Good to go. Read more

I replaced the freezer door seal. Read more

Had to replace the auger. The auger on my ice maker was made of plastic and had broken pieces off it. The new one is made of metal and seems to work much better. Was a fairly simple repair. However pay close attention when disassembling, I recommend using your cell phone and snap a pic of the different stages as I became a little confused when putting it back together. Ordered the part and it was here the next day. I'm very happy to have my ice coming down the chute again. By the way, I'm a 70... Read more

The auger would not turn the dispenser because the screw threads were stripped. I could not re-thread it so I had to replace the entire motor assembly. The video your company provided was extremely helpful not only for fixing the problem but to give me the confidence to do it myself. It was a very detailed video that included all the safety instructions. Read more

Bought gasket from website, followed easy helpful video instructions, perfect fit. Read more

I ordered the complete assembly ice bucket and all Read more

I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles. Read more

I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again. Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The... Read more