Kenmore Washer 110.91320100 (11091320100, 110 91320100) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 285664
Replace a cracked, leaking, or worn washer drain hose. 48 inches long with clamp included. Installs between pump and standpipe for proper drainage.
Do-It-Yourself Stories from Customers like You
Drain hose too short and home depot fix leaked Sara B. • Liberty Hill , TX • August 21, 2015
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly.
Now we're washing again and no leaks!
Read more
More
$31.95
- Compare At:
-
$38.02
- You Save:
-
$6.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3362624
Replace a cracked, broken, or missing timer knob on your washer. This control knob installs on the timer shaft to adjust wash cycles and settings.
Do-It-Yourself Stories from Customers like You
Broken washing machine timer knob. Steven K. • Bronx , NY • August 28, 2023
I ordered a replacement knob which I received the very next day, and replaced the broken knob.
Read more
More
$32.95
- Compare At:
-
$39.54
- You Save:
-
$6.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62780
Used to lock washer cabinet to rear wall of washer.
Do-It-Yourself Stories from Customers like You
Slightly imbalanced load in the washer created a a lot of noise. Marvin F. • Williamsburg , VA • March 13, 2014
Replaced springs and the ordered clips holding the control panel to the washer outer cabinet. Clips had been elongated from earlier repair work. A DIY tutorial was a great help.
Read more
More
$15.95
- Compare At:
-
$17.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9724509
These lid bumpers are sold individually.
Do-It-Yourself Stories from Customers like You
(1) motor drive coupler (spider) broke / (2) lid switch cracked at screw hole which allowed it to drop down causing the switch not to activate without rigging an extension on the lid actuator post David S. • Hillister , TX • May 04, 2016
Replaced both with ease after reviewing video. Parts matched OEM specs perfectly. ***Shipping time was excellent - placed order with standard package delivery at @11pm on a Tuesday evening & received the order in Southeast Texas Thursday morning @11am.
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10131112
Agitator not moving clothes properly or spinning weakly? This straight-vane agitator restores wash action in 10 minutes with basic hand tools.
Do-It-Yourself Stories from Customers like You
Agitator broke Joann K. • Watersmeet , MI • June 10, 2022
Replaced it
Read more
More
$88.40
- Compare At:
-
$105.20
- You Save:
-
$16.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21258
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
Do-It-Yourself Stories from Customers like You
Whirlpool washer David L. • Linn , MO • August 31, 2015
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved.
Read more
More
$11.95
- Compare At:
-
$13.33
- You Save:
-
$1.38
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8519200
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
Do-It-Yourself Stories from Customers like You
No spin/agitate. Daniel S. • Landenberg , PA • November 11, 2022
In the end, with a new coupler. But I relearned old lessons the hard way.
The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned...
Read more
More
$12.40
- Compare At:
-
$14.63
- You Save:
-
$2.23
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3946532
Washer motor shield deflects water, lint, and debris away from the drive motor. Replace if cracked or missing to prevent motor damage. Simple install.
More
$20.49
- Compare At:
-
$24.38
- You Save:
-
$3.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62750
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
- Misalignment of components
- Unusual noises during operation
- Difficulty in assembling or disassembling parts
- Reduced efficiency of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, four are needed to replace all parts. Screw part number WP3390631.
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10109200
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
- Fastens panels, brackets, or internal parts to the cabinet/frame
- Helps maintain alignment to reduce vibration and rattling
- Replaces lost, stripped, or corroded screws
- Common symptoms: loose panels/trim, rattles, or a screw that won't tighten
What's included: One screw. Install notes:
- Disconnect power; shut off water or gas if applicable
- Match thread and length to the original; replace one at a time to keep alignment
- Start threads by hand to avoid cross-threading; use the correct driver
- Tighten snugly—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Missing baffles Anna S. • Shoreview , MN • January 31, 2016
I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62691
Rubber grommet for motor mount stud.
Do-It-Yourself Stories from Customers like You
Washer did not agitate Gary S. • Kimberling City , MO • December 26, 2016
Replaced dog ears.
Read more
More
$8.95
- Compare At:
-
$10.56
- You Save:
-
$1.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3347034
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Wife noticed water on the laundry room floor! Richard L. • Phelps , NY • April 06, 2015
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and...
Read more
More
$49.40
- Compare At:
-
$58.29
- You Save:
-
$8.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96160
This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.
- Connects water tubing between components within the appliance's water system
- Helps maintain a tight, leak-resistant seal at the joint
- Restores proper water flow when a tube or connector is damaged
- Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit
What's included: One adapter tube assembly. Install notes:
- Disconnect power and shut off the water supply before servicing
- Relieve line pressure and place a towel or pan to catch any residual water
- Note routing and orientation before removal to ensure correct reassembly
- After installation, restore water and check all connections for leaks
Do-It-Yourself Stories from Customers like You
Washer not filling with cold water Stephen S. • Bronx , NY • July 24, 2016
Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks.
Cold water settings now work properly again.
Read more
More
$11.51
- Compare At:
-
$13.58
- You Save:
-
$2.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820044
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Do-It-Yourself Stories from Customers like You
Power cord got pinched and shorted out Gary D. • Kentwood , MI • July 27, 2014
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops.
Read more
More
$78.95
- Compare At:
-
$93.95
- You Save:
-
$15.00