Kenmore Refrigerator 363.58772894 (36358772894, 363 58772894) Parts

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

After reviewing a number of testimonials and your videos from your APP.com site I determined my most likely problem was either the defrost heater, thermostat, timer or possibly all three. The real challenge now began. Getting to the specific parts with my specific model number was a real challenge. It was not as easy as removing the light guard and 5 screws since my model had two Track Cant Shelf vertical rails restricting the removal of the back panel. Also, these rails could not be removed... Read more

• Noisy

I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the... Read more

• Leaking

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

• Leaking
• Ice maker not making ice

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

Replaced the water supply valve...boom! Read more

• Light not working

When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more

I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more

• Noisy

I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more

Replaced springs, flapper assembly and ice door retainer as described in videos and it was easy. So far so good..water dispenses. Read more

I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more

Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more

Replaced the Evaporator Motor Read more

Installed new stainless steel pan replacing broken original plastic pan and installed new rubber grommets for the compressor Read more

Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more