Kenmore Refrigerator 363.9532780 (3639532780, 363 9532780) Parts

Ordered the part through e-mail based on the model number of the frig. When the part arrived,I looked at the set up from the right side and follwed the process for the right. Took me one minute. Read more

• Noisy

I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the... Read more

• Leaking

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

I found that the Ice Maker in my GE side by side made ice but would not kick out the ice when it had formed, the heating element or the switch that controls it didn't work. I ordered a new ice maker switched it out took less than 3 minutes. The cord was very stiff and just long enough but I got it to connect and in 35-40 minutes I had fresh ICE!! Read more

• Leaking
• Ice maker not making ice

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

I ordered a new bucket and auger combination--I didn't want to have to completely disassemble the mechanism to replace the rusted auger helix dispenser, so for about twice the cost of the auger alone I got the complete assembly. The product arrived in pristine condition less than 48 hours after I purchased it online. About 10 minutes later (most of that spent taking out the old bucket and finding my philips head screwdriver), I had removed the four screws holding the cover plate on the old... Read more

• Won't start

I bought this relay switch and it works great. On the left side of the compressor there is a plastic cover you pry off with a screw driver. The relay switch had one wire plug on it. Just pull the wire off and the pull the relay switch off the compressor. Read more

Replaced the water supply valve...boom! Read more

I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more

• Noisy

I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more

I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more

Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more

The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket. Read more

I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more

Easy fix once I found the problem. Broken solenoid sleeve. Part cost $2.58 + shipping. 10 minute repair. Read more