Kenmore Dishwasher 665.13124K702 (66513124K702, 665 13124K702) Parts

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

Repair was easy. Just slotted the new parts in and they fit and worked fine, Read more

After reviewing the other repair stories related to this "7 blinking light" syndrome, I contacted their support staff via Chat. I relayed my symptoms along with model number of dishwasher. She indicated that this would normally mean an issue with either the heating element, the high limit thermostat, or the control board. Since the control board was so expensive and (luckily) out of stock, I ordered only the heating element and the thermostat. After pulling out the dishwasher and removing... Read more

Ordered front panel and panel control. Also ordered name plate (did not need) front panel already has it. My husband and I had it switched out in approx 10 minutes. Took longer to gather proper tools than it did to do the repair. Looks awesome and original! Read more

Ordered the parts and followed the instruction videos that Sears provide, Initially tried to order parts from Sears directly but the web-page kept complaining about my shipping address. Their loss- no wonder they're going out of business. Also, should note that the original assembly was plastic but the replacement was metal. Sure sign of a crappy cost-cutting decision. Overall, very happy with Appliance Parts Pros! Read more

First tried replacing the seal around the door as that was the simple and most logical fix. Still leaked. Removed the front and upper panel to inspect. Found calcium deposit running down from under the Air Vent Assembly and wet behind the black stick-on insulation. Easy to trace the leak to the bottom of the door. => Ordered new Air Vent Assembly, gasket and Vent Deflector. Parts arrived. Took 5 minutes to remove upper panel. Removed the two wires from the Air Vent Assembly. Inserted a... Read more

I replaced the seal which turned out to be a little tougher job than it was supposed to. Small screws and very limited space to get into. Use a magic nut driver or something to hold the screw. Read more

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Removed and replaced diverter motor. Ops check good, no more leaking. I'm guessing the seal was the problem but diverter ruined (water residue) from leaking over the last 5 years??? This seal is only available if you buy the tub so followed another review - removed diverter then gently pried out the seal, cleaned and then lubed with silicone grease. Also turned the seal 180 degrees or the opposite way before reinstalling the diverter and then wrapping it all back under the counter. Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more

Pulled a video from online and ordered my parts from Appliancepartspros.com. This was the second repair I've done with your help, the last being my washing machine. This time I replaced the dishwasher detergent dispenser on my Kitchen Aid. You guys make it so simple and give me the confidence to do it myself! Read more

• Leaking

Took off cover, installed new parts. Read more

I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without... Read more