Need Help?
Call
Central hub that connects the inner tub to the drive shaft in washers. Replace if corroded, cracked, or arms have broken off causing wobble or imbalance.
Looked online at several websites to see if I could figure out the problem Came across AppliancePartsPros video on replacing bearings. Watched it a couple of times and determined (well, guessed) it was the bearings and/or spider. Followed the video (great job by the way) and disassembled the washer. The spider was cracked on one arm so ordered a new one from this site. I also ordered two new bearings and the bearing seal b/c learned from the web and local appliance store that they go bad in 7+... Read more
Fix detergent not dispensing or a broken dispenser drawer. This washer detergent box assembly holds and releases soap properly. DIY-friendly repair.
I replaced the dispenser assembly and since this was being replaced, I installed a new drawer and detergent box assembly. Read more
The Washer Circulation Pump Motor is an OEM replacement part for LG washing machines. It is a vital component responsible for circulating and pumping water through the wash tub during the various wash and rinse cycles.
Symptoms of a faulty circulation pump motor include:
Causes of a bad circulation pump motor can range from normal wear and tear over time, electrical malfunctions, blockages or obstructions in the pump impeller, or physical damage from foreign objects or debris.
This OEM LG part is also compatible with Sears/Kenmore washing machine models.
Replaced the drain pump and circulating pump units. Read more
Fix detergent not dispensing or leaking from drawer. This dispenser assembly includes compartments for detergent, bleach, and softener. 15-minute DIY repair.
Secures the inner door gasket to prevent water leaks during wash cycles. Replace if gasket is loose or leaking. Confirm fit with your model number.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Shipping bolt assembly secures the washer drum during transport. Replace if bolts are lost, damaged, or missing before moving your washer to prevent damage.
AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more
Washer not spinning or making loud grinding noises? The rotor assembly commonly fails when splines strip. Moderate DIY repair in 1-2 hours with basic tools.
Replaced rotor assembly due to hub being stripped. New part was upgraded with steel insert. After watching youtube video on AppliancePartsPros site, it took about 15 minutes for entire job. Part arrived in two days. Great service. Read more
The Float Assembly is an OEM part for LG washing machines. This part monitors and controls the water level within the appliance. It's a safety feature that prevents water overflow and potential flooding, contributing to the efficient operation of the washing machine by maintaining the correct water level for each cycle.
Causes of a bad Float Assembly can vary from simple blockages that prevent the float from moving freely to electrical faults within the switch mechanism.
Symptoms of a bad Float Assembly include:
This OEM LG part is also compatible with some Kenmore models.
The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more
The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.
Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.
Symptoms of a bad vent hose include:
This OEM LG part is also compatible with Sears/Kenmore.
Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more
Filters debris from water entering your washer. Replace when water flow is reduced or sediment buildup occurs. Verify fit with your model before ordering.
I was cleaning the supply hose filter screen constancely, I had no Idea there was filter screens in the pump intakes on the machine. once I found them and replaced them, I had plenty of water, so don't buy supply hoses with the screens in them until you check to see if your machine has them already. Read more
The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.
Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.
Symptoms of a bad clamp include:
This OEM LG part is also compatible with Sears/Kenmore models.
If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more
Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.
Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.
Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more
Directs water from inlet valve to detergent dispenser in LG washers. Replace if hose is cracked, leaking, won't stay attached, or damaged from wear.
I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more
Replacement suspension spring for washer tub support. Installs between cabinet and tub to absorb vibration. Replace if broken, stretched, or missing.
Our 10-year-old LG WM2487HWMA front load washer had gradually developed multiple problems. It sounded like a jet engine during high speed spin, both the drain pump and circulation pumps were noisy, it would not drain properly (water was coming in during spin cycle), no water was spraying out at the top of the door into the drum like it is supposed to when the circulation pump was running. It's amazing we had still been able to wash clothes at all! With the help of the excellent... Read more
Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.
Took top off and did a line at a time Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.