We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.
Took top off and did a line at a time Read more
Most orders arrive by Wednesday, November 25
This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.
I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more
Includes sensor probe
This noise filter assembly is an electronic component that suppresses electromagnetic interference (EMI) generated by the washing machine's motor and control circuits. It helps prevent electrical noise from feeding back into your household wiring. Replace this part if your washer fails to start, shuts off unexpectedly, or causes interference with nearby electronics.
Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more
Replacement bolt that secures the spider assembly to the inner wash basket. Needed when hardware is missing, stripped, or corroded during repairs.
Can't buy LG parts in Canada without getting an LG Tech to install. $1000 repair was too steep for me so went on websites and bought from Appliance Parts. Watch the video on Appliance Parts. Note - Joyce from Appliance Parts really helped in identifying the bolts that I needed. Read on and you will see why. Stripped down machine and identified the spider had failed along its three arms. Bearings were still in good condition. Managed to get three bolts off spider but remaining three had same... Read more
Concrete balance weight mounts to washer outer tub to stabilize drum during spin. Replace if cracked, broken, or missing to restore proper vibration control.
My problem was a broken spider. I followed your excellent video, but have some additional input that should be incorporated in a new video showing the required upgrade procedures and parts required to repair an early model with damaged front tub half using currently available parts. Don't expect everything to go as easy as the video. 1) Used 4lb. brass hammer to drive shaft from bearings. 2) Torqued spider bolts to 20ft lbs. with thread locking compound. 3) attached rubber seal to front tub... Read more
Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.
I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more
Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.
I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more
This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
Replaces a frayed, melted, or damaged power cord on your washer. Restores grounded connection from wall outlet to internal power circuit.
After I looked at the video from you guys, I said I can do this, so I placed the order. When I received the power cord I started changing it, was so easy then after 15 minutes my washer was working. Thanks you. Read more
Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.
Replaced Read more
Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.
I went to your web site found the part using the model number of the washer machine. Also with the part picture, there was a video showing step by step instructions. They were very clear and was breeze replacing the hose.Doing this myself saved at least probably $150-200. Appliance repair shops quoted me around $80.00 just to come out. Then they mark up the price of the hose at least twice the cost of what I paid , They too have to order the part and come back to install. So the labor was what... Read more
This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.
Joins two internal water lines in your washer. Replace this coupler if cracked, worn, or leaking to restore a secure connection during fill and wash cycles.
Following what I've seen or watched from you tube video clinic "how to replace drain pump for LG Washer, model wm2277hw and the help that I received from representative/ customer service of appliacepartspros, I fixed our LG Washer no problem. I am very much thankful to the representative of AppliacePartsPros who help me analyzed the problem and recommended the right parts that I needed and most importantly arrived 2 days as ordered. I would recommend AppliacePartsPros for ordering your parts. Read more
Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.
The dealer gave us a door but it didn't fit. Everything we bought from Appliance Parts Pros.com was fixed with just a screwdriver. Easy and fast. Shipping was fast also. The longest time was installing the hinges on a stacked washer and dryer. Read more
This washer tub assembly is the stationary outer drum that contains wash water and supports the spin basket and drive components. Replace a cracked or worn tub to stop leaks and restore smooth, quieter spin performance.
First we called for "professional" help. Those guys took $60 of our money and said, "Get a new one, it'll be cheaper than having us fix it." Then I found this site and videos and saw that other people had the same problem I had, common for LG washers after about 7 years, when the bearings fail. If I could replace just the bearings, it would be cheap: your site had the new bearings for around $65. But I saw another user recommended getting a new rear outer tub assembly to save time and the... Read more