Lg Washer GCWP1069CD Parts

The LG Model LG Washer model WM2487HRMA ISSUE: Washing Machine was filling very slowly. Overnight it would fill about 1 or 2 gallons. I would clear the tub by pushing a) Power b) set spin to None c) push Start. That would empty the tub. REPAIR SOLUTION: That did not solve the problem. Second, I replaced both the single (1) Water inlet valve assembly Part Number:5220FR2006H and also the Water Level pressure switch Part Number:6601ER1006E That solved the problem. I can't tell you which... Read more

I replaced the Tube to pump hose which was very easy. I just tilted the washer on it side and replaced the Hose. Read more

Replaced the drain pump and circulating pump units. Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

• Will not agitate

Swapped bad part for new part. Read more

This was Kenmore front load washer made by LG. Model 796.41302610 First, AppliancePartsPros.com has been great. This is my fourth time using them. Staff, DIY comments, and videos are all very helpful. Always ended up with the right part and received next day. The machine made an odd noise on start-up. I ran diagnostics. Had a problem finding how to do diagnostics since the instructions in the manual were wrong. Found the correct process on YouTube. Needed to hold the spin and soil buttons... Read more

AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more

I opted to save myself about $600 by repairing my 8 year old LG washing machine rather than buying a new one. After watching some videos I determined what I needed upon taking my washing machine apart. I ended up replacing the tub (includes spider and shaft), since I could not get the spider part removed from the original tub, as well as the motor bolt (which had broken when I removed it from the original tub's shaft). The spider was cracked and the shaft was wobbling which caused it to... Read more

• won't spin
• Will not agitate

I looked on the internet for similar descriptions for similar models and found many angry reports. Most said that the rotor assembly was bad as the nut that held the rotor and other parts together had loosened and allowed slippage between steel and plastic splines. Yes, I know that sounds like trouble, but apparently not to LG when they designed it. Most buyers complained that the part was covered by warrantee but not the labor and labor had been quoted as $400 to $600 dollars. Time to buy... Read more

The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more

Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

Our 10-year-old LG WM2487HWMA front load washer had gradually developed multiple problems. It sounded like a jet engine during high speed spin, both the drain pump and circulation pumps were noisy, it would not drain properly (water was coming in during spin cycle), no water was spraying out at the top of the door into the drum like it is supposed to when the circulation pump was running. It's amazing we had still been able to wash clothes at all! With the help of the excellent... Read more