Lg Washer WD-11276BD Parts

Changed out door switch and door latch hook. Watched video it was so easy. Appliance Parts Pros save me hundreds of $$$$. This is the 3rd time I used this company I must say they are the best. Read more

My front loader LG washing machine wasn’t working correctly. The clothes were either coming out unwashed or completely dripping. When turning the washer on it would start up like normal and the turn off a few minutes in. Initially it was not displaying an error code, this made it very difficult to diagnose. One of the kids started a load not knowing we are having issues and it started making a clunking cringing noise, when I went to investigate the EL code was up. A few YouTube videos later... Read more

The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

Can't buy LG parts in Canada without getting an LG Tech to install. $1000 repair was too steep for me so went on websites and bought from Appliance Parts. Watch the video on Appliance Parts. Note - Joyce from Appliance Parts really helped in identifying the bolts that I needed. Read on and you will see why. Stripped down machine and identified the spider had failed along its three arms. Bearings were still in good condition. Managed to get three bolts off spider but remaining three had same... Read more

My problem was a broken spider. I followed your excellent video, but have some additional input that should be incorporated in a new video showing the required upgrade procedures and parts required to repair an early model with damaged front tub half using currently available parts. Don't expect everything to go as easy as the video. 1) Used 4lb. brass hammer to drive shaft from bearings. 2) Torqued spider bolts to 20ft lbs. with thread locking compound. 3) attached rubber seal to front tub... Read more

I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more

Replaced Read more

Replacement Read more

Replaced spider arm, bearings, drum seal. AppliancePartsPros had the overall cheapest price and factory parts not knockoffs. Had all my important parts <2 days and the rest on the third day. Good on line tutorial ideas. Good company. Will do business again. Read more

Parts arrived as expected. AppliancePartsPros video's were extremely helpful. Making this repair quick and easy. I will definitely look to AppliancePartsPros for help in the future. Read more