Lg Washer WD-12410BD Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

• Will not drain
• Noisy

It was fairly obvious that the washer drainer motor had failed, water was not draining, filter was clean (bottom lower left panel door, have a pail ready!) and drain line was not blocked. Someone had provided great advice on the Appliance Parts Pro's site about replacing the drain motor from the bottom. Great suggestion! Easy to do, although be prepared for more water to drain from the washing machine onto the floor after you lay it over. I carefully lowered the machine onto it's back,... Read more

• Will not stop filling with water
• Leaking
• Shuts off too soon
• Will not fill with water

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

• Leaks water

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

Repair went fairly smoothly by following the EXCELLENT how-to video provided. I had only a few issues and suggestions. 1. Because many of the screws and fasteners are of multiple sizes, I would recommend laying them out in a muffin tray or on a paper with labels for where they go back. 2. After removing the weights and prepping to remove the shock absorbers, after the front ones were removed, the tub tilted so far the rear shock absorber separated. The friction pads fell out. It was easy... Read more

I watched the Appliance Parts Pro video and saw that it was a job that I could easily do. I ordered the Rotor Position sensor switch for about $21 on a Monday and it was delivered by UPS on Wednesday. The process was straight forward: 1) remove the back cover from the washing machine (4 screws), 2) remove the main bolt holding the magnetic drum on the motor; 3) remove the 6 bolts holding the coil on the motor; 4) remove the ground screw and wire harness clamp screw; 5) take the old sensor... Read more

First and foremost, much thanks to APP for perfect transaction, and incredible price! The part was shipped quickly, and arrived fast. Immediate Availability of the part was outstanding, and truly saved this Canadian's day! See, in Canada, LG has their own unfair practice of NOT ALLOWING a Canadian citizen to purchase ANY functional parts for any of their appliances or products... furthermore, in order to get the part for any issue, you must pay directly for an LG direct service tech to come at... Read more

The repair was fairly straight foward as shown in the video. However, driving the shaft from the bearings took some doing. It required replacing the use of the board with a spare bolt and a 2lb hand sledge. (having an air hammer as reserve, also not a bad idea) I rated this reair as a "1" however I've been an auto mechanic for 40 years. If you do not have good general mechanical ablities you may find this more challenging as you get it further apart. I suggest anyone making this repair should... Read more

• Will not drain

Unscrewed the leaking filter and replaced with the new one. End of problem. Great service and prices at Appliance Parts Pros.com. This will be the first place I check whenever I need repair parts for any of our appliances in the future. Read more

Replaced the drain pump and circulating pump units. Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more

My problem was a broken spider. I followed your excellent video, but have some additional input that should be incorporated in a new video showing the required upgrade procedures and parts required to repair an early model with damaged front tub half using currently available parts. Don't expect everything to go as easy as the video. 1) Used 4lb. brass hammer to drive shaft from bearings. 2) Torqued spider bolts to 20ft lbs. with thread locking compound. 3) attached rubber seal to front tub... Read more

• Won't start