Lg Washer WT5270HW Parts

Fix squealing or grinding noises during spin cycles with this washer motor rotor assembly. Works with the stator to rotate the drum. Video guide available.

Fix dispenser overflow or leaking issues with this washer detergent drawer assembly. Channels water through detergent and softener compartments. DIY repair.

Hardware washer that sits beneath screws or nuts to distribute load and secure fasteners. Replace if bent, missing, or worn to restore proper fit.

This small cover cap conceals an exposed fastener or opening on your appliance, restoring a clean, finished look. It also helps protect the area from dust and splashes for a tidy, long-lasting installation.

• Covers and protects an open screw hole or attachment point on a panel or door
• Restores a clean, factory appearance
• Helps keep dust and moisture out of the opening
• Common signs it's needed: missing cap, cracked/broken cap, loose cap, won't stay clipped

• Disconnect power (and water, if applicable) before servicing exterior panels or doors
• Note the cap's orientation and any retaining tabs before removal
• Use a plastic pry tool to gently release the old cap; press the new cap until fully seated
• Avoid forcing the cap or overtightening any underlying fastener to prevent damage

This clutch housing assembly supports the clutch coupling in the washer's drive system, aligning and securing moving components that shift between wash and spin. Replacing a worn housing restores smooth engagement and consistent agitation and spin performance. What it does:

• Houses and supports the clutch coupling that engages the basket for wash and spin cycles
• Maintains alignment of drive components to help prevent slippage and noise
• Helps transfer motor power to the wash plate/basket through the clutch mechanism
• Common symptoms of a failing part: no or intermittent spin, weak/no agitation, grinding or scraping noises from the bottom of the washer

• One clutch housing assembly

• Disconnect power and water; turn off supply valves before servicing
• Access is typically from the bottom—tilt or lay the washer carefully and support it securely
• Remove rotor/stator and clutch components as needed to reach the housing; note fastener locations and wiring
• After reassembly, rotate the drive by hand to check for binding and run a test cycle to verify agitation and spin

Fix a leaking or cracked fabric softener dispenser with this washer softener cap. Easy DIY repair with no tools needed—just remove and replace in minutes.

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Washer won't spin or agitate properly? A worn stator disrupts the motor's magnetic field, preventing drum rotation. Moderate DIY repair restores spin.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

Replace a cracked or clogged washer nozzle assembly to restore proper water flow and prevent poor cleaning performance. Moderate DIY repair.

Balancer assembly mounts to the washer basket to counterbalance loads during spin. Replace if cracked, damaged, or causing excessive vibration.

Genuine hardware washer that distributes fastener load at assembly joints. Replace if worn, cracked, or causing loose connections. Confirm fit with your model.

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

Replaces a cracked, rusted, or damaged tub cover assembly that attaches to the outer tub rim. Prevents water leaks and splashing during wash cycles.