Samsung Refrigerator RF263TEAEWWAA Parts

Replaced cap handle. Repair took less than 5 minutes. Read more

Order a new fixer Read more

I used Live Chat with ApplianceParts Pros and I had a great gal who would not quit till we found the proper part for my refrigerator. I applaud your customer service especially Cindy H.! The part arrived quickly and I had already read from previous people on your website who had fixed same part what their experience was and it helped when I had to install mine. One mentioned that it was flexible so I knew what I needed to do. Flexible is the KEY word on this particular part. I inserted one... Read more

I called our local appliance repair shop. Because it was the Friday before the Labor Day weekend, they were not able to make a service call before the following Tuesday. After viewing the 'how to' video on Appliance Parts Pros, I ordered a replacement hinge plate and pin. The part arrived the following day, Saturday, and it took all of ten minutes to replace the hinge and remount the door. It does concern me that the part is labeled a "Best Seller", so maybe I can look forward to more hinge... Read more

• Leaking

Hooked water line up and has worked fine. I need to return the unopened part. Thank you Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

Repair required removing all of the interior drawers & shelves and the interior back panel. There you will find the defrost heater. Behind the defrost heater is a metal plate as well as one on the back of the front interior cover. Both were corroded and in need of replacement. I ordered Samsung part #’s AP5577767, plate drain & AP5587916, evaporator plate and replaced both. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Replaced original parts- Only skill needed was finding plastic push tabs. No tools required. Most of time was used for removing food from refrigerator before looking for tabs. Read more

Entire Samsung Ice Master is modular. Ordered the "ASSY CASE-FAN AUGER MOTO " part and replaced original...Removed ice basket. Removed Cover-Wire Harness by removing screw and unplugged both the modular icemaker and part mentioned above. Icemaker is removed by sliding forward and down. The "ASSY CASE-FAN AUGER MOTO" part at back of ice compartment is held in by plastic clip on bottom of compartment. No screws to remove...just lift up clip and slide forward. Replace parts in reverse order.... Read more

Replaced the fan that circulates the air. Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

I purchased this piece and it fit & work perfectly Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

Removed broken piece, installed new piece. Read more