Samsung Refrigerator RF323TEDBSRAA Parts

After discovering that our leaking fridge was caused by a plastic water storage tank I went on the hunt to find a replacement. Sadly there is no replacement available instead you have to purchase the entire filter tank assembly. Since I only needed the tank I carefully took apart the new unit and removed the tank. The biggest hassle is making sure you go slow so you can remove the front of the housing. Then the right side of covers the tank, pump and lines. The lines are the easiest to... Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I watched the videos and bought the parts I needed then replaced them Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

Replaced refrigerator evaporator compartment fan. Read more

Ordered a replacement hinge. Read more

I replaced the control board and the microswitch. Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Order a new fixer Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

After 3 warranty companies wouldn't honor their warranties (they said they only covered mechanical failures) I turned to the internet and found this site. Not all of the parts have pictures so I chatted with a person on the site who gave me the part. Ordered it (even though I was nervous it wouldn't be right). It came and my husband was able to fix our fridge for $23. Thank you so much for all the help. Read more

Repair required removing all of the interior drawers & shelves and the interior back panel. There you will find the defrost heater. Behind the defrost heater is a metal plate as well as one on the back of the front interior cover. Both were corroded and in need of replacement. I ordered Samsung part #’s AP5577767, plate drain & AP5587916, evaporator plate and replaced both. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Entire Samsung Ice Master is modular. Ordered the "ASSY CASE-FAN AUGER MOTO " part and replaced original...Removed ice basket. Removed Cover-Wire Harness by removing screw and unplugged both the modular icemaker and part mentioned above. Icemaker is removed by sliding forward and down. The "ASSY CASE-FAN AUGER MOTO" part at back of ice compartment is held in by plastic clip on bottom of compartment. No screws to remove...just lift up clip and slide forward. Replace parts in reverse order.... Read more

Replaced the fan that circulates the air. Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more