Samsung Refrigerator RF4289HBRSXAC Parts

• Fridge too cold
• Fridge too warm

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

Replaced the French Assembly (flapper). Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Removed the bottom shelf by releasing the 2 clips near the water filter, then lifted the front of the shelf and slid it out. Removed 2 screws from the broken Vegetable Rail and replaced it with the new one. Slid the shelf back into place and locked it down into the clips. Done. Took longer to remove everything from the shelf than it did to fix it. Less than 5 minute repair. Read more

Ordered new drawer which the picture made the face of the drawer appear gray. Called an operator she said it appears all drawers are fac tory gray face border. Ordered two day shipping and was pleasantly surprised when drawer arrived on time with white face border and matched original happy happy happy. Read more

I removed the broken rail saving the 2 Phillips head screws for installation of new drawer rail. Removal of the shelf above the drawers was required and was accomplished by pushing a button on the front of the shelf support. The installation was a snap and took about 10 minutes after removal of food items. The part was the correct one as verified by the model number on the inside of the refrigerator door. Thanks AppliancePartsPros.com! Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

I replaced it. Read more

Ordered leg. Cover and magnet switch. I did not need magnet switch, it came on the new leg cover. Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

Ordered new shelf. Popped out the old one. Snapped in the new one. Read more

Removed Phillips head screw from bottom side. Next I removed front electronic interface panel, carefully. The plastic clips holding it in place are designed to pop lose on the right side first.then unplug wiring from back of interface panel. Remove two Phillips head screws holding ice/water dispensing unit in place. Carefully remove dispensing unit from leaving multiple wiring plugs connected. Carefully apply pressure to the side of the ice chute door frame to remove the ice chute door/flap.... Read more

New flap housing with a new spring and the new replaceable guide. I didn't know the screw to hold the guide to the housing and forgot to add the spring bushing to my cart during checkout. It was pretty simple, only reason I didn't give it an easy rating is because having to pop off the hinge caps was making me think I was going to snap some of the cheap plastic, kinda have to be careful Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

Removed refrigerator panel, disconnected light and fan power. Removed fan assembly and replaced motor, grommets and fan attachment spring. Unit had adhesive on spring to help hold the spring. Chatted with customer service and clarified that spring and fan would easily pull off motor shaft. Adhesive probably was extra measure used during original build of the fridge. Noise was due to fan rubbing on housing. New fan position set to avoid any rubbing. Read more

Removed refrigerator panel, disconnected light and fan power. Removed fan assembly and replaced motor, grommets and fan attachment spring. Unit had adhesive on spring to help hold the spring. Chatted with customer service and clarified that spring and fan would easily pull off motor shaft. Adhesive probably was extra measure used during original build of the fridge. Noise was due to fan rubbing on housing. New fan position set to avoid any rubbing. Read more