Samsung Washer Dryer Combo WD18H7300KP Parts

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

I opened the washer and replaced the pump. To open the washer: 1. Remove the 2 screws that are different from the others in the top back corners of the machine. That will let you remove the top. 2. Remove the soap tray and its holder. The tray comes out if you depress the tab in the back center. Its holder comes out if you remove the two screws in the front. You can leave all the hoses attached. 3. Remove the control panel. It snaps in. Undo the top snaps first. You'll have to reach... Read more

• Leaks water

Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more

• Will not agitate
• won't spin

My washer would not spin. This fixed my problem only took me 5 minutes to uninstall and install. Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

I watched the you tube video that completely explained how to do it. It was very easy to do. Read more

• Door latch failure

I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more

Ordered a new knob and took out little bits of the old one. Took the new knob and pressed it over the stump and presto works like new. Read more

Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more

I replaced the main PCB in the back bottom of the washer. Simple exchange of pcb. All I needed was a phillips screwdriver and a second set of hands while all the cabling was moved from the original main pcb to the replacement pcb. Washer works like a charm now. Read more

With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more

Removed top panel to reach the hose and sensor. Propped the washer back, reached up to remove bottom hose assembly. Replaced with new hose and new sensor. Put top panel back on. Parts place told me the part was backordered for months and repair would cost at least $80. Got it in three days and fixed it myself. Read more

When I opened the rear cover and check the temperature sensor, I noticed the wire connection was damp. I dried it up with a hair dryer and it worked again for a few days. Then the problem came back. When I gone back to inspect the second time, i noticed a lot of water on the floor. I knew there was a leak. I followed the disassemble samsung washer video from "Repair clinic.com" to open the top cover, then i realized the assembly hose was busted. I ordered the parts from this site and... Read more