Samsung Refrigerator RF27T5201S9 Parts

• Ice maker dispenses too much ice

I replaced the ice maker after replacing the ice try and before that the ice chute gasket. All easy fixes. However, I am still seeing some frost build-up leading me to believe that the issue is just a faulty design, which I have read other posts on. Just too much warm air gets in the ice maker because it is located in the refrigerator, plus warm air probably finds its way from the outside dispenser, up the chute into the ice maker. Oh well, nothing the occasional hair dryer won't take care of,... Read more

I noticed that the bottom of the plastic bucket was cracked even though it was less than two years old. I called Samsung and they wanted to charge me almost $200. Instead, I found the part at appliance parts pros for half that cost. Since I replaced the ice tray bucket assembly, my ice maker is working perfectly! Read more

Poped off plastics caseing inside the frigerator. Unscrewed 4 screws holding black fan inplace. Followed yellow wire to locate white sensor. Need to be careful not to break styrofoam, don't force it, it should seporate from plastic easy as long as the 4 screws are out. Swap it for the new one and button it back up. While I was in there I replaced the defrost sensor and the other sensor next to the heating rod. Also I know there is an issue with drain hole plugging up with ice so I extended the... Read more

Repair went great thanks for your service Read more

I loosened middle hinge by the 2 screws which holds a power cord that clips together, then slid the hinge flap upward to release from the door. My bottom clip hinge was broken away from spring and the only way to attach a new hinge clip was to carefully separate the hinge flap. This can be done by squeezing the flap to see where the separation seams are. Small narrow screwdrivers along with a spatula will do without damaging the plastic. This allowed for acess to the spring which connects to a... Read more

The easiest repair I've ever done. I originally thought (after watching some youtube tutorials) I would need to replace the spring on the flap, but it is not accessible on our Samsung model. Undid the two screws holding the flap to the fridge door, pop it up off the other supports, and un-clip it from the power cord. Put the new flap on the same way and all done! Delivery of the part was crazy fast too! Read more

Replaced chute gasket and ice bin. Has worked great so far. Fingers crossed. Read more

• Light not working

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more

I replaced the cooling fan. Read more

Just took off the old part and put new one one Read more

Replaced shelve Read more